Search results

VERY nice work. It can be extremely time consuming to get that nice smooth symmetrical finish.

Price drop $120 shipped in the lower 48.

The Yamaha's like a little higher popoff. Get it up to 45 ish +/-. Also I've seen this wierd low to mid transition problem particularly on the 701 with dual 38's if the little check flapper on the back of the jet cover is too thick OR been doubled up.

I recycle everything metal. I WOULD do plastic too but there is NOT a recycler here for it??? If I'm walking trails, riding a watercraft, kayaking, at the boat launch,....I will pick up other peoples trash cause it pisses me off! I buy second hand whenever I can, MOST of my shop is second hand...

I have a set of new 'freestyle' mats (glue on) for an SXR......at least, I think I've confirmed that's what they fit. Rear of tray pad where it curves out is 17" wide and from there to the front is just less than 30" long. If you want them just make me an offer. I'd also trade for a working...

My wife takes Meloxicam every now and then for shoulder pain, good stuff. Pretty sure it's bone spurs that need ground down but it only bothers her if she uses that arm a lot in one day. ....Now AFIB too??? Damn, you're falling apart bro LOL!!

There is good info here. I always feel great after a few days of eating healthy. I try to stay away from much fat fried foods and starches. My nemesis is Mountain Dew, allthough lately I've cut way back as the wife and I are going back to the gym 5 nights a week...........I'm exhausted! I've not...

Do you just want the 'nostalgia' of owning the correct Yamaha part number? Cause for about the same money you can buy a much nicer 'True RMS" digital meter that will do everything that little junker will do AND a lot more. Or you can buy a compareable analog meter for about $20 that will STILL...

The trailer build IS pretty sweet! I swear dude.....we're long lost cousins or something LOL! I've been working on the wife's Superjet, my Tigersaki, had to replace a few floor joists and an 8ft section of wall on my house, I have my buddies '72 Scout engine and trans in the shop, my son's '66...

I might need to try a set of tubbies on my Tigersaki.

My father in law has made a few hundred thousand day trading penny stocks.....you HAVE to watch it a few times a day EVERY day. There are some sure bet stocks and ways to make quick cash. I've lost a bit in the last few years but I knew it was a gamble. I find it's much more fun to go to the...

I actually clean the threads and smear a bit of moly grease on the coupler threads. I do this to any engine.

Milled and squished head.....32cc. Nice little compression bump and still run 90/91 octane fuel. $125 shipped in the lower USA. Send me a good core and I'll take $30 OFF!!!

Nice to see somebody offering these again.

This is an oem head that I rechambered and milled, still slightly staggered as original was. Depending on your setup this will be anywhere from 170-190psi. 95-100 octane fuel $150 shipped.

No different than a body shop taping weatherstripping around a window. Careful prep, that's all.

Once in a great while a Yamaha "charge" coil will go out. It's the main power generating coil for the ignition. You need to backprobe the brown wire with white stripe coming from the stator....put your other meter lead to ground. Start it up and watch AC voltage. should be 30 volts +/-. Then...

Guys, I've been using 'Leak-Lock' for years...

My Tigersaki is running 45ish with more tuning yet to come. Twin carb 640 Tigershark engine and electronics. Stainless single carb 640 pipe. Stock 550 waterbox. Blueprinted 550 pump, bored nozzle, Skat 14/17 repitched to 9/20. Jetsport deep 2 bar grate, Ocean Pro long ride plate. Stock sponsons...

I can't believe nobody has jumped on this yet. My local Facebook has beat up stock crap for this price!!