Search results

I cant find a definite answer on this. I got the shaft and rear bearing out with no issues (lightly tapped on the end of the shaft)... The forward most bearing doesn't want to budge in the press, before I put too much pressure on it, can someone confirm which direction I need to be pushing on it...

thanks for the input. Next up, is this the right prop to be using for my '96 rn (see info on signature).. Took it apart 2 years ago when I bought it to repaint (played with it twice) and just getting it back up and running now.

They can actually rebuild missing surface area as advertised ? I took a couple good knicks out of the leading edge of it, in an act of desperation I ground it down a bit to try to flatten it out and eliminate the cavitation issues, but to no avail, it hooked up, but it about rattled the ski...

Need some advice. I have a skat trak 9-17 prop that has been chunked up via some rocks at the launch ramp. Anyone have any experience with Impros or can recommend someone similar ? Is it worth throwing upwards of $100 at this, or should I hang it on the wall as a souvenir and start shopping the...

This has probably been asked a million times, but I am going to ask again because I am yet to find it.... Where is the one thread that has pics of everyone's custom painted skis ? I need some ideas.

Looking for how the plastic front end piece attaches to the ski, it slides in under the front, and then I remember a screw goes on each side in the back, but wasn't there some kind of washer/spacer/compression something that went in there so as to not mash the plastic with the woodscrew ? Pics...

Cannot for the life of me figure out a 650sx, it runs good for 15 - 20 minutes then gets hot and only idles (I presume fuel is boiling). Get back to the ramp and let her cool and all is good again. Engine has good compression and did a leak down test on it, it held a vacuum for well over and hr...

That's a start, Im thinking of ones that were specific to the size of the ski, they were whole paint schemes with elaborate designs, similar to some of the paint jobs Blowsion puts out (I know those are custom)....

Years ago I remember seeing somewhere online that one could purchase vinyl templates, stick them on the ski and paint around them.... whoever was making them had several different patterns to choose from. Does anyone have any info on these or know where to get them? Time for a paint job.

Whats everyone's favorite neoprene life vest without any ski scratching zippers or buckles ? Must be USCG approved. Priced lowest is always best. Christmas is coming.... Your recommendations?

Anyone have some how to's on rebuilding the midshaft? It's been a few years since I have taken one apart, which way do I press the shaft out of the housing?

Cheap / best place to find a few gaskets for my engine? Need the intake and exhaust mani gaskets, carb gaskets, and the gasket that goes from manifold to the factory headpipe. Let me know. Thanks.

whats a decent price to be paying for used? FYI - I am talking about my '91, see my signature for setup.

Is there someone out there that does work on props and pump housings/vains to bring them back to workable condition? I mangled my Scat-trac being stupid at the ramp and sent a few nice sized rocks through the pump. If not, where can I pick up a prop affordably? This was a 9-17 and seemed to...

got any pics of the aftermath? my underhood area looks terrible as is.

Best price I could find on the interlux linked below. Just ordered, I'll give it a try. http://www.jamestowndistributors.com/userportal/product.do?part=28062&BASE

i see worst marine offers a pettit epoxy product for $29 a qt, anyone played with this stuff? http://www.westmarine.com/buy/products/21084-ez-bilge-paint-white-quart.html?cid=sc_google&creative=10408039924&gclid=CIeKyuKImq4CFULd4AodWhrYKg

dont want to spend the money for awlgrip. Any other cheap suggestions?

I have everything out of my ski and am looking to put a nice coat of white under the hood while it is knocked down.... I saw a few pics floating around here in the past, what did everyone use?

What is the best source / cheapest price on Wiseco pistons?