Search results

Sold

I forgot to mention the polished exhaust manifold and ceramic coated headpipe. The ignition is Advent with four programs adjustable by dip switch. I had Advent program four timing curves that Art (Jetworks) laid out for this motor. Two are for race gas and two are for pump gas. I'm also...

Thanks for the kind words Paul. Hope you are doing well.

Sorry about that. I forgot to put the location but I just edited it and it is in Central Jersey.

All the goodies $4500. Pick up in Old Bridge, NJ. I'm moving on to other hobbies. Those who remember this key and engine combo no what it is and that I was never too hard on skis as I enjoyed building them more than riding sometimes. You're getting a pretty good setup but it is currently...

No torque spec (except not going so tight as to strip the teeth on the stainless clamp band). I think you may have an alignment problem. Position the headpipe and chamber without the coupler on and see if they butt together smoothly/uniformly. If one is at an angle to the other (due to...

If you look at most of the sites that describe files, you'll see that they state whether or not it came with the Windows operating system. In this case it did not. It is therefore not a big problem to delete/uninstall it. Worst-case you will break a program that you added after the operating...

Also, in general, any time you get pop-ups like this or unknown processes, do a Google search on them. There are numerous sites that describe the process and what it does. I second CCleaner. If you're running Windows, Microsoft Anti-Spyware cleanup tools are great too (no need to have MS Anti...

Just a heads-up for others. I bought this one a few years ago: http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=37824 I then replaced the bolts used for our flywheels with grade 8 bolts and grade 8 washers and it has done me well on iterally removing 20+ Yamaha flywheels...

Check with Asbury Park too. You guys had one there about five years ago. It's still a somewhat depressed town that might welcome the money being spent at local establishments.

He set his goal for Daytona to complete a backflip and succeeded. Not too shabby for a reinforced 08 SJ with a 709cc motor. See pic. Congrats Kenny. Keep it coming.

Still got the ADA big bore 933 (7mm). Love it. It's as nasty as ever, but to be 100% completely honest it's too much power for me. This year I am commited to learning how to ride better. For that, I'm building a stock reinforced hull with a worked 701 to ride in the surf. I've been hanging...

Stock porting, ADA head, lightweight charging flywheel, Enhancer. single ATP intake with Novi 48. I'm pretty sure he'll get it next time out too.

blaster800, it looks like you did everything except use a multimeter inline to observe the amount of current draw. Am I correct to assume you are going to start disconnecting wires until you no longer get a spark at the battery? I don't think this is the best method because a spark at the...

The coupler is a billet UMI or ADA aftermarket coupler. It uses the Kawi 5-finger biscuit. It's smaller in diameter and as such a little harder to align, so take your time when installing it. From the looks of your side-by-side pictures, everything looks to be the same position-wise between...

I tried that in the past and just tried again. vBulletin recognizes that it is not a valid image file. EightySeven550 PM me your email and I will send it to you to figure out how/where to put it.

I'd say that John's (Jet Ski Solutions) is the one to go for. It comes with Tygon tubing. With clunks, you need them to be "heavier" than the tubing that they are attaching to. With Tygon you get that as it is very soft. With all that other stuff that people sell in colors and such, even if...

Absolutely you could use that Blackjack. I'm not sure what you mean by "race carb" except perhaps a carb that someone can't figure out how to tune the low speed circuit on.:bad3: The foundation of that Blackjack is a 46 Mikuni, the same as Novi. Not sure if you are going to see a big...

When you add in the time it takes for Jetworks to stop fixing skis and building motors (top-notch performance for better than typical rates by the way) to talk with you and ship this to you do you really believe that there is a 20,000 markup? As with any product, materials, alone, do not make...

Yes, on a stock pole. I ran it for a season without the backing plate and it was fine. Eventually I went to a True Value and they had stainless tapered flat head 1/4" bolts that were longer so I bought them and added the backing plate. On most of the aftermarket poles the bolts they supply...