Search results

Contemplating if it makes more sense to purchase items individually as opposed to purchasing a complete rebuild kit. Most of the time, I only replace the gaskets and filter and not the spring arm, spring, etc... Also wanted to confirm which gaskets to use when rebuilding a set of 38mm Mikuni...

Super minty freshwater parts skis. Anyone looking for a 95 Wave Raider exhaust? Sent from my iPhone using Tapatalk

I'm talking running skis WaveRaiders, Venture, VXR pro, etc... the whole thing: hull, pump, steering, electronics, motor... The whole nine yards. Sent from my iPhone using Tapatalk

I realize there's always stories of someone getting two running waverunners and a two place trailer for $150, but I suspect this is more of an outlier as opposed to the norm. I wanted to see what people believe is a reasonable price for given configurations. Monday night I'm going to pick up...

@smithrookie, was the motor you used in your build a stock 62t case, 61x cylinder motor or had the cases or cylinder been ported? Remember a two stroke motor is nothing more then a heavy air pump and if you port either the case or the cylinder, you are changing the amount as well as the...

I'm not using aftermarket flame arrestors, I'm sticking with the OEM air box. Inside the air box, directly above the carbs is a layer of three stainless steel screens which are designed to keep any sparks/flames from shooting back out of the carbs. The three screens are also a bit restrictive...

So, I took a set of 38mm Mikuni SBNs and pulled the choke shafts, pressed in new brass primer nipples and plugs, swapped high and low speed adjusters with T handles and installed new rebuild kits on each. They're now sitting on an OEM intake which is connected to a stock 701 motor with a...

So, since it was Gomez throwing the stunts, why wouldn't they just use his Edge? I doubt RR would have bitched about licensing and such. Sent from my iPhone using Tapatalk

So... yesterday's episode of Animal Kingdom started off with a jetski scene with the guys on two couches, a B2 and a black SJ with tubbies and an RRP pole. Character Deran Cody goes from riding on his knees on the SJ to throwing multiple backflips and huge barrel roll. So, who knows who got...

That was my plan. My only thoughts were: After I press the grease packed seals into the nose of the stator, do I have to throw the whole stator back in the oven to warm it up again and what will that do to the rubber seals or the grease? I wonder at what temp grease starts to liquify? Also...

Historically I've fully assembled my driveshaft, stator section and bearings. At that point I grease up my pump seals with water proof grease, slide them down over the driveshaft and "TRY"to press them down into the front of the stator section. Problem is I use sealed bearings (3 bucks on...

Yes, you will be required to remove your skis from the beach and return them to the campsite each evening. I will take my ski via my hitch hauler, so you're free to use my trailer which is setup for three stand up skis. Also, my twenty year old daughter and sixteen year old son will be...

Don't be the guy who thinks you need to put 3M 5200 on the intake manifold studs where your carbs bolt to. Also don't use it on the pump side and diaphragm side screws on your carbs. Argh.... what do people think?!?!? BTW, anyone have a set of the stand off things that bolt to bottom of a...

Last weekend we had a little pre-freeride session with the Buffalo crew. Sent from my iPhone using Tapatalk

Absolutely.... Wristbands are in hand and T-shirts will be done next week. Sent from my iPhone using Tapatalk

I'm talking about the intake manifold studs to which the carbs are bolted. The four nuts came right off, but the base of the carbs are essentially welded to the intake. Sent from my iPhone using Tapatalk

So, I bought a 2004 SJ years ago and shelved the stock 701 motor and dropped in my JM781. I just got around to using parts from it and was unbolting the carbs last night and found they are fused to the intake manifold. I think the previous owners put 5200 on the carb studs. Before I totally...

Blaster peeps, Plan on making my own gas spring hood lift kit. I've determined the 20" expanded and 12" compressed (8" travel) gas springs are what I need, but I haven't figured out what compression weight to choose. Options are 20, 30, 40, 50, 60, 90 & 120Lbs. I was thinking two 20Lbs gas...

Yep... it's the Presque Isle peninsula. Sent from my iPhone using Tapatalk

We were chatting about that with the screen printer. We could offer it as a V-neck or a tank top. I'm open to suggestions and I'm pretty sure the screen printer will work with us. I did find out 2XL is an extra $2 per shirt. Sent from my iPhone using Tapatalk