Search results

Remove the rubber block from the bottom case, block off oil pump, and change exhaust and your Venture powerplant will be happy in any SJ. You can use the lighter 6M6/61X flywheel and stator combo as well. As me mentioned earlier the Venture had staggered jetting as well, it would be good to go...

Better on ebay :) http://bit.ly/1osygAg Bet you could get them to knock off $20 if you call and buy direct, seeing as they would pay $25 in ebay fees! Sent from my iPhone using Tapatalk

Won't cause you any trouble Sent from my iPhone using Tapatalk

Badass truck! I drive a 07 Ram 2500 6.7 Cummins, 312k and counting. H&S tuned and deleted. But there's something about a blacked out Ford that gets me every time! Sent from my iPhone using Tapatalk

You'll be fine, it wouldn't be a bad idea to bag it up and Saran Wrap, keeps the air out! Sent from my iPhone using Tapatalk

Not a great idea to mix and match carbs to make a dual setup. Your FW and electronics will swap right over. Fuel lines are really no harder on duals though... Sent from my iPhone using Tapatalk

In reference to your first post, you will need a new intake manifold, your 62T 38 mani will not work. Stock 44 manifolds are pretty cheap, and came on the flowing: 96-97 Blaster 2 Raider and Venture 760 XL760 GP760 You can use the same reeds interchangeably between the manifolds. You will...

Dual 500 Rules with a Tidy Bilge setup from OCD of course ;) Sent from my iPhone using Tapatalk

Quick tip for anybody who pulls their cylinder and forgets the remove the coupler beforehand (like if you are replacing crank seals). Take 2 small pieces of 2x4 and put them on either side of the rear rod, across the case top surface. Put a 1/2" socket extension wrapped with a shop rag through...

If you want to return the SBT one, you can pick up a harmonic balance puller at Advance, they have 2 kits that are $10 and $17 and will work great for you. Grease the main screw and use an impact gun if you have one. Also use the shortest M8 x 1.25 bolts you can and she should pop off easily...

I have used freight quote.com a few times, pretty cheap. My guy there is Craig Chaney Sent from my iPhone using Tapatalk

My old boss is a dealer here in NC for Rance Trailers, their Renegade line is full aluminum and is amazingly built. He has a 12' model that I have personally put thousands of miles on with zero complaints. They are pricey, but super nice. Sent from my iPhone using Tapatalk

Hey guys, couldn't seem to find an answer to my question on an existing thread. I am looking to get a Solas 144 Mag Pump as they seem to be a good performance upgrade at under $500. However, I don't want to spend close to $300 on a Hooker or similar impeller, because I already have a 08+ RN...

Yes, that is the factory crank for that motor.

Bump, I have the same questions.

Dammit, I was gonna make almost the same post! I was gonna say "Some students bring books when they go back to school...." Anyways, I had a load goin back to college - towed w/ a 1992 Ranger In bed: 1994 CBR600 Stunt bike & 1994 Ninja, along w/ house stuff and clothes Behind truck...

Solid price, where you located?

A 2003 overdue? HA! My rule of thumb w/ 2 smokes is run em till they go! 25 LBS low on a cylinder will still run well, but it's out of spec for sure (10% on 150 is 15 LBS acceptable difference). I have owned/run 1990 SJ's w/ original motors, and dead on compression - just depends. I would...

As always, excellent insight on your part, Charles! It really helps back up a point when you explain well....

That's what a DEPOSIT is about - and unless noted otherwise, is non-refundable. That makes it worth the seller's while to hold the ski for you - that way if you back out, his time is compensated for. Bottom line, your deal was completely fair. You lost $200 because of poor planning, and...