AlbanyMotorsports
Cru is Rad
- Location
- Chicago
Does anyone else besides WDK have an upright kit for the 66e setups? I am looking for one and clearly going through Jeff is like trying to turn a bolt with a spoon.
66e Upright Kit
- Thread starter AlbanyMotorsports
- Start date
SXR-FOREVER
Finally Flippin
- Location
- Lake Minnetonka, MN
I may be picking up a ski this week with one in it. Pm me wednesday or thursday and I should know if I'll be getting it or not.
SUPERJET-113
GASKETS FOR CHAMP BRAP!
- Location
- Lake Havasu City, AZ USA
AlbanyMotorsports
Cru is Rad
- Location
- Chicago
Thanks. I would prefer to stick with the set of cases that I have already but I will definitely reach out to brandon about that setup.
SXR-forever I will touch base with you soon. Definitely interested in teh setup if you get it.
SXR-forever I will touch base with you soon. Definitely interested in teh setup if you get it.
With his setup, you keep your upper case half, send it to him and he matches the new bottom to it so you can keep your ported upper case if that's what you're worried about.
AlbanyMotorsports
Cru is Rad
- Location
- Chicago
Still in search of an upright kit. Spoke with Brendan who sounds like he has some great stuff going on right now. I would prefer to find the bolt on tabs at this point. Any help would be great.
What about just buying some plexiglass from lowes or something and glue up a template for a machine shop to fab? Maybe even wood... I'm not that familiar with what all has to be done but I bet figuring out a way to mount a lower case (not the entire heavy engine) to something else wouldn't be that hard.
Mock up an ugly @ss mount and tell the shop to weld some 0.125"-0.200" thick steel in that shape and then prime and paint it. Might take a little more work and I'm sure you'd have to shim it to get it perfect but I bet you'd put quite a bit less than $200 in it.
Mock up an ugly @ss mount and tell the shop to weld some 0.125"-0.200" thick steel in that shape and then prime and paint it. Might take a little more work and I'm sure you'd have to shim it to get it perfect but I bet you'd put quite a bit less than $200 in it.
Last edited:
wsuwrhr
Purveyor of the Biggest Brapp
- Location
- Alta Loma, working in Upland
Don't forget about what you will need for exhaust for that.
The mount is the easy part.
Brian
The mount is the easy part.
Brian
AlbanyMotorsports
Cru is Rad
- Location
- Chicago
Ive been runnin the 66e stuff for a while now. I need to bolt it into a different hull that only has sj mounting holes.
wsuwrhr
Purveyor of the Biggest Brapp
- Location
- Alta Loma, working in Upland
- Location
- Plymouth, MA
i have two brand new ones, T6061 machined ready to go. 275 shipped usa.
also have, complete kit, bed plates, pipe, intake 1500 shipped
2 x complete 84mm motor ported with Riva valves and Kit 3000 shipped no carbs
pat
also have, complete kit, bed plates, pipe, intake 1500 shipped
2 x complete 84mm motor ported with Riva valves and Kit 3000 shipped no carbs
pat
Attachments
Last edited:
Shifty
- SuperJet Thursday -
- Location
- Austin Texas - Lake LBJ
Nice stuff.
AlbanyMotorsports
Cru is Rad
- Location
- Chicago
Thanks guys. PM sent.
Idok
F1pro
- Location
- Nations oldest muthaF+++kin city
very nice pat!!!
- Location
- Plymouth, MA
wdk.
note / correction motor kit has no carbs and no pipe.
i have 1 pipe and novi gen 2 46mm carbs that can be added
- Location
- Plymouth, MA
No problem at all.
