Search results

That is one beat up SXR!

Dang, this is the same hull I was planning on learning flips and rolls on too! Guess I'll just have to reinforce that area during my winter build...

Yes, I would agree with you on the sitting for years issue, but the exhaust valves dropping, flywheel bolts breaking, ECU resetting, and most of all SC clutches shattering are very common problems with these RXPs.

We purchased three 2005 RXPs earlier this spring from a guy who had modded two of them and left them to sit for 3-4 years in his garage. One of them had bad SC clutch washers. We replaced the clutch washers in all three as well as the oil pumps in the one that failed. All three ran great so we...

Is there anyone in Ohio with an FX1 that I could ride? Looking at an FX1 AM hull, but would like to try one first. Sooner the better! You would be more than welcome to ride my 730cc drypiped RN or stage 3 RXP. I will likely be riding Saturday at Delaware resevoir or up at Erie around East...

$6000-7000 would be a fair price for that ski WITH those mods. I have a 2005 RXP with a stage 3 Riva kit, rear exhaust, bigger IC, etc and while it is pretty damn fast, it gets boring quickly. We keep ours around incase one of our standups need a tow; the rest of the time the chicks ride it...

This would have Tom21 tubbies and wide tray mod, would that make a significant difference?

Is it a good all-around ski? Setup will likely be a 771 or 850 Xscream, Solas 144 mag, Thrust trim, etc. Would this setup be able to flat water flip or would that be a stretch?

Anyone? I'm trying to decide wether to buy this hull or wait for something better... really wasn't planning on getting anything until winter. My riding buddy picked up a full carbon REV hull for $2500 a month ago but I'm not sure if I'll come across a deal like that this winter or not.

So I'm considering picking up a full carbon WDK F1 Pro. I've been riding a stock hulled RN for about 1.5 seasons. Anyone have any experience with the F1 hull? I ride 75% flatwater and 25% baby waves at Erie... How do they handle compared to the SJ? Are they ridable at a reasonable speed for boat...

Is this hull still in production?

Been waiting two months on a ride plate... don't think I'll be using them again.

So my started up my Superjet the other day after a nice 1.5 hour ride and noticed that the idle is bouncing quite a bit. Today I pulled the carbs off to change the jets out and a few other minor mods and it did the same thing when I went to start it up. I've never had this happen before; Anyone...

I've been trying to get my ski tuned properly since I finished up the build a month ago but I'm still having problems with low end power. Motor is a ported 62T 730cc with dual 44mm SBNs, 190psi comp, Solas 13/17, and a R&D drypipe w/ Jetworks water injection. Jetting specs on the carbs: 115...

+1 on all of the above. I was trying to get a deal last fall on my first ski and spent $3100 on a modded 2002 SJ from PA that turned out to be a huge POS. Previous owner was a huge dumbass that half-assed everything on the ski. After spending several months rebuilding the ski from the ground up...

Got it today, thanks

I originally ordered the plate via phone, but they no longer list their phone number on the website. They responded to my email inquiring about the lack of a shipping notice the same day I sent it (July 10th). I sent them another email today via their website (not through my email) so I guess...

Well Fast Elements friggen sucks. I ordered the plate on June 26th and my card was charged on the 28th. A week later I still hadn't heard anything so I emailed them and recieved a response on July 10th saying my plate had shipped that day but no tracking number. As of July 20th I have not...

I found broken reeds in my buddies ski. The rubber coating was coming off of the cage and one of the petals was missing and others a little chewed up.

I'm having the same problem with a buddies ski. Haven't been able to figure it out yet either.