Search results

It'd b easier to just buy a nozzle setup for trim, but has anyone tried drilling and tapping a nozzle not setup for trim? Those nozzles are made of cheap "potted" metal. I was unsure how well my threads would hold up in a raider nozzle.

Im sure it's been posted already but I love watching the old retro vids.

I'm for sure not a composites guy and claim to know very little. For those that are: I made my last TL mount plate out of what I thought was Lexan 1/4" thick polycarbonate. Does anyone know if the Optix version of the same stuff is as durable? It's listed as only a 1/10 as strong as lexan...

What's the diameter and length of the long exhaust tube for a RN? I know the SN is a bit smaller, but don't know the official # for either.

I'm missing the comedy video u and Mcdog put together yesterday at the pig trail. Where is it?

All of a sudden I'm having trouble with the X on my Iphone. I always use the "lightweight" version when on my phone. Everytime I log on make the switch from "Darkness" to "Lightweight" and when I navigate from the original page that I selected it reverts back to "Darkness." Is there a setting...

This has always been a background thought in my head. It may be heresy for me to ask since Mikuni's are so prevalent for the basis of modified carbs, but here goes. Growing up in the late 80's I rode mx bikes quite a bit and pretty much read the words off of any motocross mag I could get my...

Ive seen numerous discussions around this topic. I'd like to hear from guys who've made the swap directly from bpipe to PFP with exactly the same setup. I want seat of pants impressions: bottom end hit, how quickly it runs out, jetting changes, set up troubles, any maintenance ... Cost is a...

title says it. And, can a 62t cdi be used in place of a 6m6 cdi (or 61x cdi) with a 61x stator?

Anybody know what the size (metric or ASE) of the Skat prop tool? I need to grab a wrench after work to fit it. I was thinking 3/4" but couldn't remember.

What's the best method for testing a coil (other than a visual test for spark)? I think I'm narrowed down to a shoddy MSD single pole coil.

I've been having intermittent spark issues with my MSD TL. I think it may be due to plug wires. I can remember reading some posts in the past with peeps dogging the msd wires. These are used plug wires I borrowed with the owner saying they gave him trouble in past too. I pulled the wire...

I just installed a double pickup MSD TL this past weekend. Wired up and running fine this weekend. Ran the battery dead. Installed fresh battery today. Was very difficult to start. Finally fired and went to ride...felt like I was running on one cylinder. Confirmed with intermittent spark...

Anyone know the ID of the OEM Yamaha long exhaust tube (and length) for a RN?

Will a SJ TDR waterbox fit in a fx1?

I need some of you guys to post up ur TL specs. I have my old settings when I ran the analog TL and a single pickup digital, but want to see other peeps dual pickup TL curves. Throw in ur engine, pipe, carb, pump, and prop if u want.

Anybody running one of the K&N dual carb flame arrestors? I need pics of the mounting hardware. Do they just mount to top of carb bell or do they have another bracket that secures them to carbs?

Where are u guys getting washers for the pump to space the impeller off the stator? What size are they? How thick? I think they're 18mm ID, but don't know for sure.

I took off from my dock today and was gonna get in a few evening minutes of riding. Ski was running normal off the dock and let it warm up for about 60 seconds and then off riding for another couple minutes. My engine started hesitating real bad off the bottom but would clean up on top. I had...

I was just looking at the Skat website. I didn't get a clear answer as to what pitches are available in mag impellers. I imagine since they state you can have the impeller pitch "of your choice" included with the complete pump, that you can get almost any pitch? Anyone have a standard list of...