Search results

I've never played with a set of keihin's. I'm assuming that the spigots marked with an "R" are for return lines. That leaves other spigots for fuel inlet, and pulse signal from cases. What is the little spigot/nipple used for? U can barely see it pointing down. Its directly in front of the...

Anyone done this swap? Will the 1x or 2t cases align? Anyway to fit 66e exhaust to x or t cylinders?

Anyone had problems with the new Epic scupper?

Who make the lowest profile (shortest vertical dimensions) flame arrestors? I need two short stack flame arrestors to fit my super chicken. Putting them on a pair of 44mm Kiehen CDK II's from a 750 SXi. Tau Ceti make some that are 1.5" tall.

This is a basic wiring question for those that have done a swap. I'm putting a SS 750 engine in my kawi SC. I have all the original wiring figured out for the old SC basics... S/S and stator. Do I need to do anything other than cap off these extra leads? I have wiring sets for oil level...

I'm trying like mad to get a handle on this ebox I have from a kawi STS. The ebox and engine are a matching set, but I'm grafting it into my sport cruiser. I have several wiring schematics, but none are specific for an STS. I have found a standard or a high performance schematic but neither...

Looking for advice. I've got a strange ignition problem. Fresh rebuild on Dasa 5mil coversion from SS PV engine this off season. MSD dual channel TL Fresh carb rebuild with clean filters, jets, and needles Ski will start, idle, and rev fine when it's cold. After 3-5 minutes of riding my...

Do OEM carbs require a different rebuild kit than SBN carb rebuild kits? Carbs are OEM 44's.

What's the dangers of running the coupler gap too narrow? I am having a fitment issue. Alignment is spot on but my coupler gap is approx 2mm. Do u risk crank damage more so than midshaft damage? At this point I may consider hogging out my engine mount holes on my bed plates to gain another...

Anyone tried to repair a oem pump shoe? Was looking at mine last night and noticed it was cracked and off set now. Was thinking about dremeling the two surfaces so it lines up and using some epoxy and glass chop to stuff in the gap then sand and smooth. May buy a new one as a back up.

Have u guys seen springs loose their color? I've got a whole assortment of springs. I even bought some fresh new ones, but I'm seeing some strange number variations with pop offs on what appears to be same gram springs. I have what looks to be 65g springs acting like 80g springs. From the...

http://www.summitracing.com/parts/SUM-UP230/Application/?prefilter=1 Anyone have experience with this stuff from Summit? I used Awlgrip but am out and Summit is near by and cheaper. Duplicolor primer is my next option.

Anyone know if a Raider steering cable will work for SJ?

I was aggressive and drilled and tapped a pump insert from M10 to M12. Believe it or not there was enough material to make it successful. However, I failed to do enough research for my new pump bolt and it is impossible to find a M12 x 1.25 in stainless. At this point I don't care if it's a...

Anyone ever had to drill out and tap the needle seat bracket screw threads? I have a SBN 46 that the seat bracket screw threads are stripped. I was either thinking about filling it with JB Weld and retapping the same size or just drilling it out one size larger. It's not a gonna be a high...

Thought this was done. I can't find it on my phone. Hook me with a link.

In the 5 years I've messed with standups I've never had to route the cooling on a completely stock engine/exhaust. My first ski came with a Riva Red pipe and I've always owned a Bpipe. I just assembled a bone stock 61x 701. Where's the system dump overboard? Someone kick me a quick diagram.

I searched the old sticky thread by 2Lick and couldn't locate this listed. I was trying to use M8 x 1.25 (I think) with no luck.

Will gp800 pump parts swap out with SJ pump?

I've run the old style xmetal shorty turn plate before, but I don't want to run straight bars. I'm looking for opinions on the other options that don't use a bearing system. I'm too cheap to pay big money for the new WDK or cold fusion steering assemblies.