Search results

I am running a type 9 dry pipe which has 1 water line going into the exhaust manifold and the other into the pipe itself. My question is can I tap the line going intot he pipe for the h2o injection? It is alot easier to get at than the other,

I just added a type 9 and an Advent. I am running 48 Novi gen 3's. The carbs are 1 1/2 turns on the bottom and 2 on the top. If I prime it it will start. After that fuel burns off it will not stay running. Any ideas?

Just hooked up my advent and I have nothing. Thought I had eveything wired up correct. I am wondering if my probelm lies in the red wire with the fuse? There a 2 red wires coming out of the advent and a red wire coming from the plug wire solenoid. I have tried a few different combos and still...

I am getting ready to install my spray nozzle into the FP exhaust manifold. It is a 1/16 thread. The hole in the manifold is 1/8. I cannot find a reducer. Am I missing something here. What do you guys with h2o injection do? Thanks

I have a water injection kit but don't have the install instructions. Anyone have a set?

I have a stock 87 550 that I put a sbn 44 on. I took it out today for the first time and it ran great for about 1/2 hour. Than I let off the gas hit it again and it started acting like it had a fouled plug. Well it wasnt a plug problem. Now it will only start at full throttle with the primer and...

What can I use to strip the coating off of a type 9 pipe?

What is the best settings on the water screws on the b pipe for top end? Thanks

Anyone here have any experience with the FP type 9 pipe on a SJ?

I have a set of 48 Novi Max flow carbs. I really like them but have heard some good stuff about the Full Specs also. Anyone here with 48/49 Full specs that might have some input? Thanks

I have a used once b mod chamber for a SJ. What are they worth?

I was looking at these on Blowsion's site. Do these help for straight line stability? Or are they just for carving turns?

I need one for my 48 Novi's and cannot get Novi, Wamiltons, Legdrag, or Riva to get back to me?

I had my SJ out today. It has a set of 48 Novis on it. I have been fighting these carbs since I bought them. The problem I am having is they won't close all the way unless I blip the throttle a couple of times. Which in turn causes a free rev condition out of the water and a fast idle in the...

Installed my b pipe last night. This is my 3rd b pipe I have ran on this 98 SJ. Last time before I installed my last mod chamber I ground down my motor mount a bit to try and prevent rubbing. This time with this new mod chamber it pretty much sits on the motor mount? Is this just the way it is?

I have a speedwerx pipe on my SJ. I had to put a new flywheel pipe mount on. After putting it on I now have to push the rubber mount over to get the pipe bracket to line up with the rubber mount. I loosened up the top 2 mounts but it did not seem to make a difference in lining up the flywheel...

Rode my 98 SJ with all my new mods I've done to it over the winter yesterday. It is a 5 mm stroker, 85.5 bore, Blowsion head (185psi), Novi max flows, v force, Speedwerx dry pipe, flow valve, MSD enhancer. You get the picture. I am running a Blowsion pump stuffer along with TBM come system and...

Blowsion girdled head what do you gap a br8es plug to?

Don't have dash panel. Can someone tell me on off reserve?

Well I just about have my 98 Superjet just about complete. I have done the following mods. 62T/64V cases Blowsion girdled head (185psi) 85.5mm 5mm Jackson Performance Center stroker Ported cylinders & cases Speedwerx race pipe Jetworks flow valve 48 Novi's Ported Riva intake Riva spacer...