Oregon Scientific AT2K helmet vcam vid.

[yamaslut]

no....


another thing:
I will be selling these too... Rob and I are gonna make up 10..
they are very rigid and will be drilled to decrease the OAW.

 

[Tuttle]

Great design. Post the video from that angle, I wanna see it :biggthumpup:

I may be getting me one of those.

 

[yamaslut]

Great design. Post the video from that angle, I wanna see it :biggthumpup:

I may be getting me one of those.

I hope to have 10 by the freeride...
special daytona offer is 75$ ea.

pm me to pre-order...

 

[hangtime]

Nice work ,you have any footage from there yet

 

[yamaslut]

Nice work ,you have any footage from there yet

I will be doing a quick edit today... I have 20 min of raw footage from that pole location... I still need to tweek the location a bit... I will get it right...

 

[Tuttle]

... I will get it right...

Can't wait to see video. Full upper body and the whole topdeck will be sweet. :biggthumpup:

 

[oxnard111]

I just used my camera for the first time yesterday. It worked great... but my mounting angled didn't work. I taped the water in front of my ski for about 20 mins. Haha, next weekend I'll try again.

 

[yamaslut]

just got done w/ the video...

I will post it in the freeride section under Pole mounted Freeride Video in about 15 min

 

[masterblaster]

I bet that will get some nice angles,but I would be scared I would get run through with it,thats a set up for good riders that never bail. way to go coming up with something new though. Looking forward to seeing the footage from this perspective

 

[special fx]

This thread is a bad influence.............I had to buy one!!

 

[feartheride]

What are the made out of ,Aluminum?

 

[yamaslut]

What are the made out of ,Aluminum?

bar stock aluminum that is drilled and tapped

 

[D Slicker]

This is what I came up with today.

 

[Jetaddict]

I just used my camera for the first time yesterday. It worked great... but my mounting angled didn't work. I taped the water in front of my ski for about 20 mins. Haha, next weekend I'll try again.

LMAO...I did the same thing when I had it mounted on my helmet. I am just gonna set up a neck lanyard for it and tuck it in my vest while I am riding. I am going to Daytona with a friend of mine, and we are just going to take turns shooting video. I don't want to take a chance missing good shots if the camera shifts down on the helmet or handlebars.

 

[Crab]

This is what I came up with today.

I havn't got mine yet, how much of that comes with the camera for clamping it to something? I was thinking of a shoulder mount somehow, seems like it might not have the head bobble.

 

[Air Gramps]

Might want to wrap in pipe isolation.... (protection and if it breaks it should float)

 

[D Slicker]

Working on protection today for it. Crab, it cam with all the mounting clamps.

 

[joesuperjet]

Let me be the first to tell you guys, DO NOT TRUST THE CLIP!!!!!!!!! My first cam and the 2 gig chip is at the bottom of the lake. Use caution with the clip. Wrap it with tape or some other type of reinforcment.

JAM

 

[meatball]

how deep is the lake and where are you located? :sneaky:

 

[yamaslut]

Let me be the first to tell you guys, DO NOT TRUST THE CLIP!!!!!!!!! My first cam and the 2 gig chip is at the bottom of the lake. Use caution with the clip. Wrap it with tape or some other type of reinforcment.

JAM

I wrap a beer coolie around mine w/ tie straps... it floats