Super Jet Where to spend my money next!?

[Parsonsjb88]

So here's my question: Whats the best bang for my buck to make a better freestyle ski, if I'm looking to spend around $1000-1500?

Current setup is listed in my signature. My 735 had a very mild seize so its due for its last overbore (84mm) which is going to cost me around $300 to fix.

What I've been considering:

Big Bore/Stroker Options
- 62T Big Bore and run 89mm pistons, 846cc, or
- HPE 809 Long rods kit, or

Bore the current 61x to 84mm ($300ish) and 1 of the following:
- New set of carbs (Something like dual Novi's or Blackjacks, etc) & a reed stuffer, or
- PFM 148 Mag Pump (http://www.x-h2o.com/index.php?threads/the-pfm-low-budget-big-pump.160675/), or
- TNT V3 complete exhaust with waterbox (From reviews its seems to significantly outperform the B-pipe)

Keep in mind any of the last 3 I would sell the parts I take off to recoup some cost. Same goes for the big bore by selling my old cylinder and head. I'm willing to stretch the $1500 limit a little, if needed. The thing I'd like to do is buy parts that will transfer over to a bigger motor down the road but thats not a requirement.

If you have any other suggestions please let me know.

 

[jo5hi3]

Is your motor 62t cases or 61x cases?

 

[Parsonsjb88]

Is your motor 62t cases or 61x cases?

62T


Sent from my HTC One_M8 using Tapatalk

 

[jo5hi3]

is your current cylinder ported?

 

[Parsonsjb88]

I ported both the cases and cylinders last summer myself.

Sent from my HTC One_M8 using Tapatalk

 

[Ducky]

What pump do you currently have?

 

[Parsonsjb88]

@Ducky: Just a standard 144, 08 SJ prop, and an 85mm bored reduction nozzle, standard cone.

Sent from my HTC One_M8 using Tapatalk

 

[jo5hi3]

I would either go with a mag pump or step up in pipe.

 

[Lumpy]

Buy lottery tickets and hope for the best. But on the realistic side of things, I've been very happy with my Hpe 809.

 

[High Speed Industries]

I'd go 809 if you are already doing a rebuild.

 

[Quinc]

Id go big bore. if you go with hpe send him your manifold and head pipe to be bored too.

 

[Parsonsjb88]

Id go big bore. if you go with hpe send him your manifold and head pipe to be bored too.

I already bored out my bpipe manifold and head pipe when I ported my cylinders. But ya I'm leaning towards the HPE 809. Mainly cause I can recoup some money by selling my crank, cylinders, head , and one of my pistons that is still like new. I think after I sell all my parts to put towards it, I can get the hpe kit, ADA head, 62t cylinders, and pistons all said and done for around $1200 out of pocket.

Sent from my HTC One_M8 using Tapatalk

 

[Quinc]

Thats what I would do, then get the pump and tnt pipe.

 

[john zigler]

You need a rebuild anyway, the HPE 809 is going to be a good upgrade BUT IMO kind of a waste on a stock pump / 08 impeller.

You should also upgrade to a 148mm / hooker.

Keep me in mind for your pump / impeller needs. We have the Solas 144, and 148mm in stock, and address the bearing fitment issues.

 

[FlightPlanDan]

I love "how do I spend my money" threads. lol.
Sillyness. Buy stock in Enron.