Search results

Okay. So I got a pretty torn up fx1 that came with a tom21 superjet 144 tunnel. How are people doing this conversion? I noticed the tom21 tunnel has superjet a rideplate recess on the side. Are people cutting more of the hull and utilizing a superjet rideplate? Or cutting more of the pump tunnel...

750$ plus shipping Comes with bracket and exhaust tube

Who has a headpipe they don’t need?? PayPal ready

How is everyone fixing these? I was thinking filling them solid would be best. Is it hard to align the motor once you do this? Any advice would be appreciated

Title says it all.

I have a jet works ported engine. 6 mil RAD stroker crank 1.5 over bore On 61x cylinder 62t cases mildly ported New prox pistons New rings, new wrist pin bearings New outer bearings and seals. Recessed domes, Used oem starter and bendix Thrust girdle kit Engine will come assembled with...

I’m looking for the protec stainless chamber and manifold!!! Not just the chamber, must have a protec mani too.

I have a rrp manifold with a pfp inner chamber set up to be run wet. would like 950 shipped, or would trade for a b pipe plus some cash on your end

I have a ebox with a year old msd with a water proof plug for the stator. Also have a lightened 62t flywheel. And dual 44’s modified by god knows who. With oem rebuilds (But hey anything has to be better then a buckshot) Can include r&d manifold with spacer for extra 400 for carbs shipped...

Up for sale is my wdk rok hull Comes with Driveshaft, pump shoe, intake grate, motor mounts, kawi pump, sxr prop, steering cable, billet pissers and bilge fitting and hood hook system. Uses Yamaha engine and kawi pump Can add other parts if wanted have just about everything to finish. Will...

I have a rrp carbon laydown chamber. Previous owner didn’t run it properly so it got a little hot. You can see the inside is peeling but not very much at all. As soon as I hooked it up properly it ran like a dream. The damage hasn’t gotten any worse. You can also see a few chips on the coupler...

I just picked these up cuz I have never seen them before. Anyone know what they are? I assumed they were buckshots.

1996 superjet 2 inches taken off back Wcf top deck and hood Glassed in tubs Xft carbon pole Reinforced engine bay Wdk footholds Jet dynamics plate 9/15 prop Umi steering plate Located in Connecticut buyer arranges shipping will not crate. 2000 obo

I have a 62t/61x engine. Has a oem crank and a fresh set of wiseco’s and a milled pump gas head. Running 180,180 It’s also 2-2 cylinder so close to perfect alignment. Can add electronics for more as well as carbs. Carbs are as clean as they come too. Engine is in a ski, but getting pulled this...

125 bucks plus shipping

So I picked up a 2010 superjet with a rrp pipe the other day and discovered the previous owner didn’t have it set up properly causing the pipe to get to hot and some of the resin fail. Out the outside where the manifold meets the pipe there are some cracks in the resin and on the inside a fair...

Deal fell thru. Hopefully this will be last time listing. I got a 2011 lenzi one hull. Hull has some work that needs to be done but if you’re even half way okay at fiberglass is shouldn’t be a problem. This hull is kinda has a huge hood so it’s really easy to work on. It is a flat water hull...

155 thrust trim with a bored steering nozzle. Not sure of model. Will come with a good used cable and blowsion trim lever. 500 obo. Will trade for superjet head, msd, ride plate, or another superjet upgrade or upgrades.

I’m trying to sell my kawi based big pin dasa engine with a 4 mil stroker crank in it. Would like to sell as a long block. Its on its first bore so it’s at 980 cc’s vf3 reeds r and d port matched intake low hour oem starter exhaust conversion plate so you can run a Yamaha lay down pipe dual...

What’s with all the hate on annular discharge carbs? Seems like the science behind it is sound. Any input would be nice. Thank you.