Search results

anyone know?:confused: thanks!!!:bigok:

Contact you representative and ask they support the Recreational Boating Act of 2007!! This is care of BoatUS: Your voice counts! And we need it to make sure the Recreational Boating Act of 2007 is passed quickly. Without this federal legislation you will need to apply and pay for a...

it was 62 and sunny today. so I pulled the ski trailer out of the garage (by hand) to go ride a little. trailer got away from me and the front, nose wheel went over my toe! :aargh4: dang toes have a lot of nerve endings! wonder if it is broken? no bones sticking out . . . . trailer...

I am putting a hi comp head on my SJ and was wondering if the water outlet on the front of the head were connected to a pisser if it would help cool the head? the stock one had this capped with my ProTec pipe. Anyone? Thanks!:biggthumpup:

yami manual says to install head gasket dry to clean surfaces whoever had the head off last time seemed to have used some kind of sealer:ugh2: does anyone use a gasket sealer compound? thanks!

I am putting a hi comp head on my SJ I need to remove the rubber lord mount off the stock head to support my pipe on the new head How do you get it off????? The ring turns but it doesnt loosen- WTF? Thanks!

Why not?

Set my vest down next to the ramp, loaded skis and went to tie them down. Thought about my vest and went back . . . GONE!:17: Any end of season deals out there ????

Sign up to win a free HS S4 at watercraft illustrated magazine. . . . FYI!!:arms::147: http://www.watercraft.com/

Is there an aftermarket turnplate out there for a SN? Mine has a AC aluminum pole and a stock turnplate. All the hot prod. etc turnplates are for 96+ SJs Anyone know where to get a SN one?:confused: Thanks!!:wavey:

For my little SN, with a little 650 . . . Stamped Yamaha and 28, supposedly made by Westcoast Anyone know what psi this head will make (looks unmolested)? This will be a good chance to check ports and cylinder walls. Wheres a good place to get head gaskets? critical install tips? Thanks!

Last week I was in Germany and was lucky enough to ride this Lightweight Germany custom flatwater backflip boat. Carbon fiber and kevlar hull. Smaller and lighter than my SN Where do I start? 701, b pipe, ADA head, UMI pole, SE trim, quicksteer, custon footholds.. this boat is the bomb!

I got dumped off my ski yesterday twice yesterday hitting submered stumps:skull2::skull2: Stumps SUCK No carnage luckily. but dang, we need rain!:lightning: New islands are appearing in the lake I ride:shocked:

2002 Civic SI Took it under the wires between N and S bound lanes and made it through :frown:: :sad:

My 750sx kept bogging and would not run. The mix was fine, plugs good, wash OK. I rebuilt the carbs and it ran OK, then started bogging again. It was like it was starved for fuel.:261: I tore into the carbs again and WHOOPS dropped the spring . . . and lost it.:headache: Back to the...

seems like more waterdawg stuff is starting to show up used. in this case: maybe they bit off more than they could/cared to chew? :smokin: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=019&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=290150916431&rd=1

I was doing nose stabs and small subs today and wiped out. Went to restart the ski and the starter kept chugging. Pulled lanyard, hit stop and it just kept chugging. Finally a buddy of mine put the lanyard back on, hit the start button and it quit.:ugh2: I let the starter cool for about 10...

these dudes just aint right:biggthumpup: <object width="425" height="350"><param name="movie" value="http://www.youtube.com/v/3jGgF32oxB4"></param><param name="wmode" value="transparent"></param><embed src="http://www.youtube.com/v/3jGgF32oxB4" type="application/x-shockwave-flash"...

I was putting in at the same itme as a 18 ft bayliner jet boat with a couple and 2 kids. spoke briefly and I was on my way. Saw them stranded on a mud bank a couple hours later. They sucked up their tube rope and locked up the pump. The guy was slipping and sliding on red mud with a knife in...

So I modded a Harbor Freight double to hold 3 skis. It was a little tricky, but I have made it work!:biggthumpup: