Search results

Has anyone ever wrapped or painted rrp pole tubes? Just wondering if they will still fit in the upper and lower pole brackets.

Anyone know if a pre 07 superjet steering cable will work on the edge?

Anyone know of a good place to buy beach cart tires? I found a place online but the want more in shipping then the tires cost. Size is 21x12x8

Anyone have a shipping company they like using and reliable? May need a ski shipped from North Dakota to New YORK

Does anyone know what the part is called that locks the turf on the back of the tray? It's a metal or plastic piece you bolt on where the bondline is.

Just looking to see if I have the right line routing on my blaster. Factory mod chamber and ada head with single cooling. Pump to exhaust manifold Bottom of head pipe to back of ada head Front of head pipe to stinger and water pisser Capped the front of the ada head line off. Just want to...

B1 with a 61x/62t with ada head. What should all 3 screw settings be for a factory pipe with a mod chamber?

I have a blaster that won't do anything when the battery is connected and button is pressed. I checked the fuse, s/s switch, all grounds and connections inside the ebox and still nothing. If I jump the solenoid it will crank over just fine. Going to swap the solenoid tomoorow and see if that...

I have a rage composites brawler with a bad vibration. Pretty much vibrates at the middle of the rpm range, to half and after half its completely smooth. I had it in the ski last year and it had the same vibration. I completely rebuilt the ski from pump to motor and it still does it. I have...

Anyone know anything about riva cylinders? I bought a 93 squarenose about a month ago, brought it home today and it has a marker welded on from riva. Just looking for some info

Looking for any info on restoring/buffing the old gelcoat on my blaster. It's lightly faded as it sits now. just planning on doing the lower half, white section. So what materials and methods do I need to do a decent job?

Does anyone know... how many and what size holes to drill for running the electric,throttle and bilge wires through a blaster hood. Also where do you drill them? In front of the steering or on the sides?

I have to props laying around for my blaster. I have a hooker 9/15 and a solas 10/16 non setback. Just looking for opinions on which prop will be better with the mods I have. 62t/61x motor mild port ada head protect pipe factory aluminum waterbox cdi with rev limiter removed

Found this H fitting on ebay. Does it matter that the flow control is on the side tube? Or should it be on the straight tube directly inline with the head pipe and stinger on pipe?

I'm switching props on my solas mag. Had a hooker 9/15 and going with a skat 10/16. My question is... should there be any gap between the prop and the mag pump? The hooker sat tightly close to the pump and the skat sits about 1-1.5 mm away. Is that normal?

Does anyone know if the lower bracket that holds the shaft to the hull is the same size as stock? I'm looking at a quick steer setup that is missing it. Just wondering how I would go about making one up or getting one.

Anyone have any idea how much urethane foam(2 part pourable) it takes to fill a tray?

Tried to save some money by doing things myself... it backfired! Pulling my motor apart to get my new big bore motor. Tried pulling the flywheel off for my first time. Well I ran one of the bolts in to far and damaged on of the coils. Does anyone have any advice on where or how to go about...

I picked up a waveblaster II last night. Ski had come off the lift in a storm and crashed on the rocks near shore. Ski sat with water in it for about 2 weeks... motor and ebox were full of water. Is anything going to be salvageable or is it just all parts?

Just bought 2 x2's today. They both have some sort of fuel injection system. Has mrd stamped on top. Anyone know anything about these?