Search results

we are riding in water temps in winter in the high 30s,with no cooling restictors running dual cooling the water temp out the pisser is still pretty much 40. what would be the best temp to run the motor by using cooling restricters?

Wondering how many of you have any luck with a total loss system in salt or surf riding,when a aftermarket coil is used and in a waterproff case. I hear this makes it much less likly to have issues? It would be for my backup boat anyway,dont think id ever have enough confidence in a TL for my...

what kind of ride time are you guys getting out of single 46,48 carbs as well as duals. We have some guys running single riva 48 power bombs burnin through a tank twice as fast as dual 38? We have a long slow wake out and back,plus a few min top end blast to get to our surf spot,so its pretty...

Have a 5 mil stroker,stock bore approx 820 cc on stock elecs,lightweight flywheel,factory B pipe,ported pump with 15/18 solas with a newly added 48 mil riva power bomb carb,what would be the best jetting,needle and pop off and starting settings for the low and high speed screw settings tried...

Have a 5 mil stroker,stock bore approx 820 cc on stock elecs,lightweight flywheel,factory B pipe,ported pump with 15/18 solas with a newly added 48 mil riva power bomb carb,what would be the best jetting,needle and pop off and starting settings for the low and high speed screw settings.

Had a fly wheel bolt come out and the wheel came off at low rpm,it has seemingly wallowed out the cranks flywheel slot,the key has a little side to side motion in it, when the wheel is put on and pushed back by hand as far as it will go,it has a few millimeters movement each way,I know when the...

http://cgi.ebay.com/ATC5K-ATC-5K-ATC-5000-ATC5000-WIRELESS-HELMET-CAMERA-4G_W0QQitemZ120333988516QQcmdZViewItemQQptZCamcorder_Accessories?hash=item120333988516&_trksid=p3286.c0.m14&_trkparms=72%3A1205|66%3A2|65%3A12|39%3A1|240%3A1318 has anyone tried the remote to this cam yet?

http://www.wavejunkies.com/phpBB3/vi...st=0&sk=t&sd=a

http://www.wavejunkies.com/trash-talk should be the top thread in trash talk with the vid named hanna

I have one of the older msd total loss systems that have the plug in chips for timing and rev.does anyone have the wiring diagram for it,its no longer on the msd site.

Just got this prop in a used pump it was cut back from impros a few yrs ago for a blaster.I dont know what it is It has a little prop shape emblem then next to that it says S0 S 18 .5 YB- M

anyone have some vent pictures of their WF hood,I have 2 large sea doo type vents in this one and the ski takes on way too much water when it flips over in the surf,they cant be any longer with this type setup? ive seen the smaller tubes a few times just cant remember how they were setup? I have...

I have a straight bar setup turn plate from x metal,I like the drop back bars that RR makes ,but they have a big taper in the middle that wont work with the clamps,are there any bars out there with 0 degree that will work like these that fit?

Was having problems out the blue with a previously flawless working set of carbs on a ski that was setup perfect,worked fine for over a yr,then ski took on some water a few times and it slowly developed a dead bog spot in the middle when you try and gas it hard,works fine up top and decent off...

http://www.x-h2o.com/threads/37099

limited setup surf boat,carbs just rebuilt,cdi replaced,stator coil seems to ohm out perfect,if you give it full throttle it pretty much bogs out or dies,if you give it quick half throttle blips,it seems to almost hit the limiter really clean.any ideas what this could be?

Last time I removed the pump they looked pretty bad,now they are starting to vibrate when reved out of the water,if anyone has a set of shafts or cheap pump with a shaft let me know

http://www.rickroy.com/ check out the steering system,it uses the bent tapered bars for even quicker adjustments,same one Pierre Maxent is using on his ski. I wonder how much shorter the tunr plate is,I dont want to use the bars with the super bend in them.The shorter bent bars look better but...

Big thanks to Fab and Kris for makin this possible for us even before they got the jetzone opened up.Their Spot on the island is unbelievable awesome.All the wavejunkies wish you much luck in your future venture. Riding reef breaks when you can see the bottom crystal clear is unlike anything ive...

Anyone get a chance to run either of these systems at tona to compare? I was impressed with how easy the wammer trim pulled while putting a little force on the nozzel,not sure what it would feel like under WOT