08 superjet

[wydopen]

hard to see in the photo, and thier not as wide as real tubbies

well it looks like people will be putting tubbies on top of "tubbies"..those probally arnt gonna cut it in the surf even with a narrower tail..

 

[YAMA CAT]

When is the Water Test?

 

[Scorn800]

Here's a pic of the side sponson from the 08 sj in havasu

 

[Ottis]

Is this hull overall shorter then the past years?

The hull bottom seems to be the same length, measured from the hull edge to start of front bumper

 

[Ottis]

When is the Water Test?

I'll have to wait till Sat., hopefuly it will warm up here by then

 

[Watty]

I'll have a new one to test by this Friday in both surf and flat water. I race and freestlye, so I'll give it a good workout too.

 

[tomski]

Motor placement is the same; longer and larger diameter driveshaft with pump moved back. The widened hull cannot match the aftermarket tubbies because of smc production. (negative draft). Sure would have been nice to see a frp bottom instead of the smc.

At least the B-pipe won't rub the sides of the hull after reinforcing.

 

[Ottis]

I was just looking under my sxr and the strake depth and placement look very close, also width of the hulls look close, light weight of a superjet and possible handling like a sxr, interesting!

 

[227]

Tom have you ridden one?

 

[waxhead]

I am expecting its just a blaster shaft
thats why its thicker as well
i hope it doesnt wear out like a blaster shaft

 

[tomski]

I thought the shaft was from a blaster but according to the part number it is completely new.

 

[waxhead]

Ok fair enough
where did you get the part numbers
i was looking to find a parts listing for the new 08

 

[#ZERO]

Is this hull overall shorter then the past years?

It's the same length but the nose goes further forward on the bottom and the rail skaggs are about a foot shorter, along with tubbies to keep the nose high.

 

[hevnsnt1]

:Banane01::Banane01: Na Na, I saw your ski before you did. Had to say it.

Here's the link I use for Erie waves. Keep me posted for Saturday night/Sunday

http://www.weather.gov/forecasts/graphical/sectors/eastgrtlakesWeek.php?page=4&element=SnowAmt

 

[luker]

well it looks like people will be putting tubbies on top of "tubbies"..those probally arnt gonna cut it in the surf even with a narrower tail..

the way the tubbies are shaped continues on in the engine compartment aswell heaps more room a b pipe shouldnt rub on the hull at all now! and where the bondline line is they are nearly flat, yamaha also used the same bulkhead which made a bigger gap in the bottom deck where the bulkhead meets, all they done is squezzed a bit more plexus in there!!

 

[waxhead]

I wish some one would make a bottom hull off a 2008
i have a top deck with a bulkhead all ready to go

 

[Tuttle]

I wish some one would make a bottom hull off a 2008
i have a top deck with a bulkhead all ready to go

I expect it will happen very soon.

 

[waxhead]

yeah i will just build one then myself
but time will tell as to who makes it

 

[Frosty]

I wish some one would make a bottom hull off a 2008
i have a top deck with a bulkhead all ready to go

I expect it will happen very soon.

maybe that's why Wammer is selling his hulls at 24% off... liquidate the old... redesign the new?

https://www.wamiltons.com/index.php...id=444&zenid=0fefdb611759fd89673f2b32ee734a1b

 

[waxhead]

good point
Maybe need to wait till the new ones come out