Will 760 fit in 93 square

[demolition_x]

http://x-h2o.com/member.php?u=877

 

[IceRocket1286]

if you dont use aftermarket pipe dont install the 760 it will not run correctly

out of curiosity, how come?

 

[marz831]

Because it's like putting the exhaust from a civic on a small block chevy

 

[Rheeder218]

whats the diff between the mod and limited b pipe? or am i looking at a diff pipe on facotrys website?

 

[demolition_x]

depends on what the plans for the motor are. if your never gonna do any porting and what not go with the limited.

 

[Rheeder218]

nope leaving the motor stock. Can you tell what that one is that i posted?

 

[demolition_x]

well your gonna want to use a sj limited pipe, then im sure you will need to get some timserts so you can use the m8 bolts. or you could drill the manifold bolts bigger and use the m10 bolts i think.

and when you order the pipe tell them your running it in a square nose if your still running 2 in exhaust. its cheaper than the rn pipe.

 

[Rheeder218]

well your gonna want to use a sj limited pipe, then im sure you will need to get some timserts so you can use the m8 bolts. or you could drill the manifold bolts bigger and use the m10 bolts i think.

and when you order the pipe tell them your running it in a square nose if your still running 2 in exhaust. its cheaper than the rn pipe.

what about that one on ebay i posted a link too?

 

[demolition_x]

hard to say. it would be a good deal for under 500.

brand new factory pipes are 650 + 20 for shipping.

when you buy used you have to worry about the adjusting screws, your gonna have to buy an exhaust gasket and some other nicnack stuff. when you buy new im pretty sure all this comes with and its brand new unmolested.

 

[Rheeder218]

hard to say. it would be a good deal for under 500.

brand new factory pipes are 650 + 20 for shipping.

when you buy used you have to worry about the adjusting screws, your gonna have to buy an exhaust gasket and some other nicnack stuff. when you buy new im pretty sure all this comes with and its brand new unmolested.

Thats all they are new?

 

[demolition_x]

yep just placed an order for mine last week. shipped friday

 

[nikad58]

well your gonna want to use a sj limited pipe, then im sure you will need to get some timserts so you can use the m8 bolts. or you could drill the manifold bolts bigger and use the m10 bolts i think.

and when you order the pipe tell them your running it in a square nose if your still running 2 in exhaust. its cheaper than the rn pipe.

drrrrrrr just tell them with a 62T manifold !

 

[Rheeder218]

they didnt make a 6m6 b pipe did they

 

[demolition_x]

actually they did, if you look under that ebay users auctions he has the manifold and headpipe from a 650. but i don't think they do any more.

 

[Rheeder218]

oh ok. well im guesing if king tut doesnt come thorugh on a pipe i think he siad he is jsut going to have to dish out for a new one. OUCH!

 

[Rheeder218]

ok i was just looking over the installation of the b pipe on this 760 motor and i was wondering how does the motor get cooled? it says to attach the water line to the head pipe. Or am i jsut reading this wrong. Is there anything that i should beaware of before we start installin and find that we need something. THanks

 

[Matt_E]

Cooling for the motor goes into the bottom of the exhaust manifold. It shares cooling passages with the cylinder. The cooling discharge dumps from the top of the head.
The water going to the headpipe is for water injection and headpipe cooling. Completely separate from the engine cooling (though usually the cooling discharge from the engine is used to feed the headpipe)

 

[Rheeder218]

yeah thats how i run it on my sea doo. Do we need to get a extra water out let as well?

 

[Matt_E]

Maybe. You used to run a stock 650, right? Those didn't have any pissers.

So, you will need one fitting.

 

[Rheeder218]

yes correct. So is there once pisser that can out the back and one that has o go out the side with this pipe?