RRP bars or other umi style bend bars...help

[masterblaster]

I have a straight bar setup turn plate from x metal,I like the drop back bars that RR makes ,but they have a big taper in the middle that wont work with the clamps,are there any bars out there with 0 degree that will work like these that fit?

 

[masterblaster]

seems umi only makes the V bend in the middle in 0 degree. anyone have anything else like this

something like this http://www.rickroyproducts.com/full...nd=Yamaha&listproducts=1&categorie=Handle Bar

 

[masterblaster]

no one seen anything like this?

 

[ChrisGooch]

Maybe try runabout bars? I know the "v" part has a laonger straight section that may fit the xmetal plate.

 

[masterblaster]

thats what im looking for,but they are hard to find in 0 degree

 

[cambo au]

i hope you find something i looked every where for these even mountain bike stores they have backsweep good luck let me know if you do find some

 

[masterblaster]

yea almost any moto or bike bar will have at least a 5 deg bend in them,If i could find a clamp that would work with the RR bars id just get those

 

[masterblaster]

http://ad-discountperformance.com/index.php?main_page=product_info&cPath=1028_81_892&products_id=686

finally find it and they are sold out? anywhere else i can find these?

 

[Scorn800]

http://ad-discountperformance.com/index.php?main_page=product_info&cPath=1028_81_892&products_id=686

finally find it and they are sold out? anywhere else i can find these?

The pic in link above is of runabout bars.

Why don't you just suck it up and buy the rrp bars:dunno:

 

[Kny21]

The description/model and pic they have there are mismatched.... the pic is a blaster bar which has sweep. Model # is for the SU 0* Bars with the V that won't work on straight bar setups.

Suck it up and mod a plate for the RRP bars. You can get clamps for the thicker bar, you just need to make new holes which might be the hard part.

 

[masterblaster]

I didnt see anywhere you can get the clamps separate,or I would already have them and the RR bars. where have you seen them for sale,RR only has the bottom piece clamp if your using the 0 degree bars that moves it back a little.

 

[butti]

I didnt see anywhere you can get the clamps separate,or I would already have them and the RR bars. where have you seen them for sale,RR only has the bottom piece clamp if your using the 0 degree bars that moves it back a little.

look at dirtbike adapters,very easy to find

 

[Big Kahuna]

UMI and XMetal are the same diameter

 

[Kny21]

you'll need an oversize bar kit.... you could possibly get away with only running the top clamp. Don't know if the bolt spacing lines up with the 7/8" spacing the turnplates have.

http://www.oemcycle.com/Item/product/3119/TR/02-2822

or else bolt the whole thing up.

Should be a hint for the guys making the turnplates... jump and start making top clamps and turnplates that accomodate the larger bars. :reporter:

 

[masterblaster]

I was looking at those style clamps before,but didnt think they would fit very well on the steering plate,they look like they stick up in the air alot higher wasnt sure if it would clear the chin pad.


I called xmetal and asked if he would at least make a new clamp to accommodate the new larger adjustable bars out there,but he said he didnt think he was going to be able to??? seems this is a much better set up to me to have at least a little adjust ability out of the running length of the pole. If i could get just the top clamps it would be no prob to drill out the plate for the new bolt spacing.