Search results

I'm looking for suggestions. I'm working on my buddies Dasa 1200. He just got the motor last year and someone else installed and tuned it for him. He has burned up three sets of orings on his domes in a VERY little amount of run time. Probably 10 hours at the most. They look like over cooked...

Can’t find it listed anywhere. What are the 2023 dates?

I am having an issue I have never had before. Since I have installed my TPE 964 I always have tons of fuel//oil all over the top of my motor that appears to be coming from the flame arrestors. I am running Mikuni 46’s and OEM flame arrestors. After every ride it’s an absolute mess. At first...

Have a local kid that needs a pole for his SN. On a bit of a budget so a clean stock one would be an option or possibly A/M.

My starter got really weak on me so I just pulled it apart. There is a brass color metal strap that goes from the positive connection over to two of the brushes that is cracked in half. Does anyone know if those are available? I see them in the aftermarket kits but aftermarket scare me since...

I want to position them so they both point towards the hull. Can they just be turned? Are they threaded in???

I’m sure someone has a 62T reed spacer collecting dust on a shelf they want to sell....... Prefer angled but open to either.

I haven't been paying attention in recent years. OEM hood gasket still the way to go? I got like 9 years out of mine on my Superfreak so can't complain, but just making sure there isn't something really good out there now for half the money or something.

Any of you guys looking to upgrade to a bigger pump have a 148 you would like to sell?

Has anyone run a RRP pipe with a Power Factor water box? How are the results? I have access to them both for almost free.

Looking for suggestions. I have been spending too much time on my buddies ski with an 1100 DASA. My Superfreak Bada?s needs more powa!!! Current set up is a 5 Mill R&D 7 port 760. Some people tell me I'm crazy for selling this motor..... I want to stay pump gas and charging ignition. I even...

What's everyone doing for trim cables on their CATS trim now days? Still Terrycable? Mine snapped. Or should I just quit being cheap and buy a good system? Have been running the CATS forever and it has served me fin.

My buddy is having issues with his DVX. Ski has a PHP 1015, PFP, Total loss, 48 novi's, Kart Tank. When doing multiple flips in a row, every single time on the third trick the ski will bog really bad. Immediately runs fine again after that and will consistently do the same thing every time...

so what is everyone's favorite GoPro? Is the Hero 5 session decent??

I am running a cast 7 port Lamey 5 mill stroker. 771 cc. Curious if anyone has feedback on a similar motor as to what they saw when comparing PFP to B pipe. Is it worth it??

I have a 5 mill stroker with a cast 7 port R&D cylinder. I don't put on a lot of hours, but decided it should probably get a top end this winter. I pulled it apart and the cylinders and pistons look amazing. Everything on the crank is tight and quiet EXCEPT the very center bearing. It looks...

Time to update steering systems and want something smooth and low maintenance. I don't want OVP steering because I can't afford to lose pole length with my back. I saw the system from Thrust and from ATP that look like huge improvements over systems of the past. Anything else I should look at?

I will be in Orlando just for the day Saturday and was debating spending $80 on a rental car. If people were riding it could be worth it rather than sitting around a hotel all day. Chad

I have my motor out and just noticed that my mid shaft has play up and down. Is that normal? I don't remember.... The bearings are smooth when I spin it.

I bought a solas mag, but am debating if I really want to install it. I am running a 762cc 5 mill cast Dasa this year. I have a superfreak and have been running it the last two seasons with the stock pump and a ported 701. I have been really happy with how it hooked up. More importantly I...