Search results

I want to rebuild my stock 701 crankshaft. I was wondering what you guys thinking about the quality of wiseco rods kit and main bearings ? Or what you guys use when building a reliable crankshaft !? Thanks!!

What is the best way to clean the interior of my b pipe chamber ?? It have a thick layer of carbon inside.

Just bought a limited factory b pipe for my stock 95 b1. Any advice, tips and settings clues before I start install!? What about the jetting?

Except piston rings, cylinder, base and head gasket, what can drop compression on 1 cyl ? ( 105 - 155 ) 105 on the rear cylinder...

I wondering if i need to put some gasket maker, a little or not at all, on my base gasket ? And on the head gasket (stock head ) ? Or it make no difference..

I'am installing my new msd in my ebox on my superjet, and i was wondering,how the e-box is getting his ground ? my negative cable from the battery goes to the engine, for the starter, but no other cable go to the ebox to give ground for cdi, rectifier etc...Last year my stock cdi blow up and i...

Does the 95 and less 61x cdi are the same as the 96+ 62T Cdi ?? Will it change my performance if I run a 61X cdi on my 96 superjet?

solas 17/23 yc-sc-1 Is this a good impeller and pitch for bottom end and flat water tricks? Thanks all

One of my friend just buy a FX1, and we was wondering if all superjet's pipes fit in the fx1? I know that the coffman sizzler fit but hard to find. Does a protec mach 1 fit ? What about the b-pipe? Any mod needed ? I will take any input about ''how to tune a fx1'' for freestyle. Thanks guys.

Can someone explain to me the way to close and open screws on my b pipe... I want to close them cuz my pipe is running to cold . So who can tell me... I close or open, clock wise or counter? Help! Thanks!!

I have a 96 superjet with following upgrades .. let me know the best way to jet my carbs ..( dual 38 ) -82 mm oversize -matching exhaust and base port, just make it mild, no enlarging. -factory b pipe -vortex ocean pro flame arrestor - stock light milled head ( 160 psi ) Thanks all!!

I got 96 superjet with b pipe, milled head 160 psi, fresh wiseco 82mm, dual 38 carb rejeted with pipe, stock intake + reed... what is the best mix I should run ... now I run 45 / 1 with standard repsol marine. with 91 octane fuel. Thanks

Do a 1993 waveblaster with 61x engine have the same starter bendix then a 62t 701 or 760 engine do? Thanks!

Someone know if a SUPERJET DRY PIPE R&D REV2 will fit in a waveblaster1? thanks

Do someone can tell me about the best way to match my 61x cylinder intake port with the sleeve. I did the exhaust cuz there are a lot more space to work and I dont want to go bigger or enlarge my port just make it smooth and equal between sleeve and cylinders... you know how stock 61x cyl port...

I want to refresh my top end to 82 mm and I was asking myself what are the best performance/reliable piston I can put in my engine? I would use Yamaha ones but they just make .25 and .50 oversize.

For me Im a atv's, sleds, bikes, mechanics ... for a Arctic Cat dealer and we sell Ktm, Aprilia, Moto Guzzi, Derbi and Piaggio too. But we repair all kind of things with a engine in it. I like my job but i'm a lot more enthralled by boats, cruisers and jets ... If only I was born in USA near...

Is this possible ... a guy I know came and tell me he will put 2 supercharge on his 62T engine in his raider. He said he will gain 20 hp by supercharge ... what should I think of this? I was thinking that supercharge on a 2 cycle is impossible ... is he talking :-):-):-):-)? Thanks!

Fot those who have cold winter... what about putting some engine coolant in my cooling system for outdoors winterisation or just move away water is enought? Thanks!

I want to know the best way to get a big engine in my superjet for freestyle .... I dont get it where u all get 1000 cc engines!? A big bore kit for 61x cyl just make a 780-800 cc bore ... does this worth it? and I 'm from Quebec near us lines in Canada ... so there are almost no pro jetkier...