Search results

Ill start by saying, I had a 650 superjet swapped it for a 701 62t. So my hull is a 92 superjet. Now the mods: motor has 160 compression, carbon tech reeds, msd enhancer, protec pipe, 44 mm mikuni single carb, solas impeller, stubby pump cone, jet dynamic ride plate, and scoop grate. Here...

I was wondering if anyone has a ebox wiring diagram for a 650 superjet with msd enhancer? I'm trying to clean up the inside of the ebox for the motor swap. The owner before me bypassed a bunch of wires.

I was just wondering what kind of reeds come with a 650 superjet? I took them apart and noticed they are fiberglass. Is that suppoes to be stock reeds?

So I just got my 62 701 in , and I was attempting to convert my 650 parts on it . Then I ran into a problem. It didn't come with a flywheel. So I thought maybe I could take my 650's and use but when I took it a part it has a broken tooth. So here is my question. My buddy has a 701 flywheel but...

I just won a 701 62t From ebay, last night. It suppose to come in sometime next week. I have a 650 with a few after market parts. Protec pipe. And mikin dual carb. So my question is what would I need to do a complete motor swap. I read that everything is compatible , but is there anything else...

So i rode saturday, and while riding I attempted to do a turn sub adn boggggggg. It would bog down and then come back to life. Like 2 seconds later it would take off. Same thing would happen when I try to jump wakes , everytime a gas it from going slow it stalls than takes off. Anyone got any...

I think someone said this is the factory scupper. I have a bilge pump, would I still need this? If so the hole that is in it, is that ok?

I'm a newbie in the standup game , but with trust of the x I went ahead and installed me some rickter footholds with mat kit from wamilton. So here it is.. The first few pics are ski with regular turf, then all taken off and cleaned up.

Does anyone have a diagram of fuel lines for 92 superjet 650? I'm trying to clean up the inside of my engine compartment , but the guy that had my ski before me has the fuel lines running all over the place. It doesnt have a reserve line just straight to the tank , filters, primer , and of...

I was wondering if I could cut my square nose pole shorter? I cant find any post on that type of mod. I see a lot of roundnose and mostly people just changeing sq pole to rd pole... If there is a thread can anyone point me in the right direction.... Thanks

I was wondering how much compression should I expect from my 92 650 cyclinders?

I have a 92 sq 650 and I was wondering if I had enough power to do a backflip? mod list: dual Mikuni 44mm carbs Protec pipe and manifold Rule bildge pump Solas Impeller not sure pitch Jet Ski Dynamics ride plate K&N flame arrestor Blowsion finger throttle R & D sponsons Rickter...

The first video I went completely under, but could not ride it out. The second video I couldn't go under all the way, but rode it out.

So I ran my super jet out of the water yesterday, and it wouldnt stop when I hit the stop button. I even pulled the key lace out and it still didnt stop. After about 2 minutes of me freaking out it finally stopped. Not sure what I did to make it stop. I was pressing the stop button like crazy...

I have searched the site many many times for footholds, and which are prefered. I aslo know that everyone says, it goes by your liking. But I have no liking because I dont have any. I went to the normal sites like blowsion and wamilton. And found rickter, digger, rec, and kicker. I seen some...

I rode my superjet this weekend Sat and Sun. On Sat we rode for about 3 hours. In those 3 hours I noticed that my ski would bog down pretty quick. It would take me at least 2 or 3 minutes to clear out before I could go full throttle. So blidge pump stayed on quit sometime. At the end of the 3 hr...

I was wondering how hard is it to install a Wamiltons Billet Stubby Pump Cone? And is it worth it ? I have Solas Impeller, not sure the pitch and Jet Ski Dynamics ride plate. Would the pump cone be good for this setup?

Ok guys I have searched for hydro turf install several times, but cant really get the answer i'm looking for. I just got my sheet of hydro turf in and want to install it today. Supplies: 1 sheet of black diamond HT, weldwood contact cement, rubber mallet, and a razor knife. I'm just doing the...

I was wondering if footstraps are good enough until I can install some footholds this winter? HOw easy are they to install? It looks like I can just screw them down . Let me know what you guys think.

I was wondering if molded grooves from hydro turf would work on my plastics for the side of my superjet? Which is better cut or molded grooves ? If anyone has any pics that would be awesome.