Search results

What is the length of the stock Superjet round nose handle pole? and where are the measurements usually taken from? I'm trying to figure out what length this AC pole is. Its suppose to be a -2, but feels like stock length and I cant stand it! Even with X metal plate and bars it feels long.. TIA

Well I just got the mid and bottom screws un-stuck by soaking overnight with WD-40 and the I used my heat gun on 850 degrees and let it heat up for about 5 minutes and they both came loose! to my suprise:arms: I thought for sure they were goin south and I was going to have to give my hard...

This a bump for Havasu Watercraft Connection and the owner Lilian Beaumer(former tuner of Multi-time World Champion Nicolas Rius). If you need a used part at a better than average used price, call Lilian. More than likely he will have it. He has a huge warehouse with shelves 10' high...

ANybody got a little drawing or easy way of cutting the rear side rail corners in turf? I'm really starting to get pissed with this HTurf. I have X molded. TIA:smile:

Does anyone know what kind of glue that Wammer used(uses) on his hoods? Like the glue that holds the intake tubes to the liner? or the same glue that is holding the liner to the hood, after the foam? It looks like a hot glue gun type of glue. My hood is prolly 4 years old...

Like the title says. Just wanting to use a extended Protec instead of the raider steering nozzle for CATS type setup. Thanks in advance!:smile:

Can anybody tell me what size drill bit i need for a 8X1.25mm tap? Is it 17/64? or mm? TIA

Just fabbed up some new homeade tubbies. What do you all think? Nice eh?:biggthumpup:

I just bought a 96 OEM hood seal and am tryin to test fit it. It seems to be about a inch or so too long. I've been dicking with it for a half hour and cant get it all to fit in the groove.:banghead: I just wanted to test fit it and maybe tape it down for a while to "train" it before I glue...

That option seems to have vanished for me? Is it gone or just me?!!:biggrin:

What is the best way to drill the trim tube? Also I havent really decided what to use for tubing either. I did a search here and PWCt and found plenty on what kind of tubing people like to use, but nothing on the drilling part. TIA!:woot:

Good seller! Fast shipping. Parts were exactly as described!(new) Paypal verified. Would have no problems dealing with again. Thanks man!:arms:

What makes people use Mikunis over Keihin's beside carbs/parts availablilty? Back in 1990 I ran a modded 42mm that was a good carb on my 88' 650SX. I replaced the stock 28mm little baby carb(good small carb too, not top end though). They are very easy to tune IMO. I think they are a quality...

My MSD dual digital TL questions thread. Anyone know how to test the single tower coils? resistance test specs? Thanks in advance! I decided to change the title of this thread because I'm sure I'll have a million questions. Thanks to all who reply!:hail:

http://cgi.ebay.com/SuperJet-Dehorner-Saw-Xlg-Cattle-livestock-Rodeo-Vet_W0QQitemZ280076523146QQihZ018QQcategoryZ46531QQrdZ1QQcmdZViewItem

Why do the 3 nuts on the back side that hold on the metal piece to the flapper hit the PVC when its slid all the way up to its stoppping flange, therefore holding the flapper open a bit. or in other words maybe easier to understand, when the PVC is slid all the way into the base to its...

Just read this over at PWCT today! Awesome, John should be in the Pro class anyways now! Congrats John and Jeff!:biggthumpup:

I wanna run some 2.5" alum tubing with silicone couplers instead of the long rubber exhaust hose from my Wamiltons "T" to the exhaust outlet.. How will all this fit with a spacer plate a dual OEM 44's? Anyone done this or have any reccomendations? At the 06 World finals SE(Sato...

Just noticed this. Dont know if you have seen it or not. Ratti on front page: http://www.apbaracing.com/

Can anybody tell me the MSD part number for the dual channel digital total loss brain box? Thanks in advance!:smile: