Search results

Any one use one of these TBM Flywheels? Weighing in at 2.0 LBS it appears to me a better decision to run this over total loss, with this flywheel you still get the advantages of total loss without the hassle and half the cost thoughts...

Thought this would be a good topic to discuss I am reading up on resin infusion and making molds does any one have any experience in this? I think I have a pretty good grasp on the resin infusion. Mark44

Bring him back. :Banane19: Mark44

Here are a few pics of my coil wire removal tool. It is made from a piece of stainless tube I cut the end and sharpened and twisted the teeth making a small hole saw with a deep throat. I simply cut the coil wire off flush with the coil insert the tool and twist clock wise and it cuts out the...

So are we on for this weekend at Kincaid? I was told it was Hawaiian night at the marina. How was the cabin trip over the weekend? Mark Katie Bob and his brother John (wetbox) Gary Scott.... not sure on this one. Lou YoYo

Forgot to post this When I get back from the Southern Fried Freeride I was going to returf my foot holds, the turf was getting pretty ripped up. I started pulling the turf off the holds and notices the foot holds were wore through and crushed inn so I repaired the holds with foam an glass...

Shorlander single place trailer I need to know tire size and I can’t check it right now. Does anyone know if they are 12.530 or 12.480? :biggthumpup: Mark44

Español ¿Que Pasa? Cinco De Mayo Fiesta esto Sabado en casa de Mark. Fiesta comienzo seis y nosotros comeremos quesadillas. Traer el plato español y cervesa. Verte allí English Whats Up. May the 5th Party this Saturday at Mark's house. Party will start at six and we...

Any one know of a place to get one cheap? Mark44

What are you running on plug gap? Mark44

FYI I sent Terry cable my throttle cable and had the wire rope replaced in it. It was getting frayed at the carb end. They replaced the wire rope and ends for $15.00 plus shipping of $6.63 and they did a great job on the cable. Mark44

Need some water tight male female connectors like in the elec. box anyone know where I can get them? :biggthumpup: Mark44

Does anyone know if the charging coils are the same between 61X and 62T? Mark44

St. Louis crew site P10 and P12 SXR-Lou Speedfreak Wetbox Katie Mark44 Scottie Now this is a BRAP party! :beerchug:

What kind of pressure is everyone running on there jet works valves. I have one on my ski and Katie is installing one on hers but I need to check pressure on both. :biggthumpup: Both limited pipes Mark44 Brap!

You know this sport is addicting when your woman is into it as much as you are. Katie is refoaming her ski installing new foot holds, scupper, trim, drains and turf. :biggthumpup: This is kick azz for our relationship. :cheer: :cheer: Anyone elses woman into it? Mark44 Brap!

Anyone see a problem with just installing another outlet next to the original outlet on the water box to run the front exhaust off of? I was planning on 2” front and 2 ½” rear. Mark44 Brap!

Your pm box is full you must delete. Now go to the beach and enjoy I will see you tomorrow.

I know Jason has a new ski but what are the specs? His last ski was a single carb power plant on a square bottom what does he have now? What is the BRAP factor and hull? Mark44 Brap!

Who is up for another party at my crib? I can grill some burgers and brats and we can sit around the burn barrel and think about riding. :beerchug: :beerchug: :beerchug: :beerchug: Wetbox is in and I will make some calls on Wed. This Saturday :biggthumpup: :cheer2: :cheer2: :cheer2: :cheer2...