Search results

What ski is that?

^^^ Do what he said. Her symptoms would probably have been worse, but I run these check valves on the end of our rigid stainless steel fuel pick tubes in the fuel tank:

It ran but it had a bog from low speed to high speed. And it was a little hard starting which required more prime pump than usual.

I stole this from somebody here, but it is appropriate to the thread: Klotz Ski Craft P.S. I just ordered two oem Mikuni carb rebuild kits, and also rear sponsons from Waxhead, so I guess this applies to me too.

How I look for things like your hose filler is first go to partzilla.com, then get the part number and/or description and put it into ebay. I did that for you, and I couldn't find any filler hose for a super jet whatsoever. Unless someone else has better ideas, you may have to buy a longer...

Opened my wife's SBN44 and found this: Didn't see it on Jetmaniac's part list, so I ordered a new oem body from partzilla.com

Curious how the @waxhead rear sponsons would compare to a Quadra-fin or Jet Dynamics ride plate. Don't the ride plates prevent slide out by longitudinal fins or a concave which -- in effect -- creates two fins, versus the rear sponsons which only prevent slide out when the ski is leaned over...

Rebuilding carbs now. Went out twice with @fx1dave aka @wavewarrior with his FX-1, but he is an animal with super human skills… (He keeps telling me to just buy a Super Jet…)

OK guys. Talk to me about ride plates. I have the Protec on my FX-1. How does the Jet Dynamics ride plate perform vs the Protec? And which one is better and why?

You could also consider a longer ride plate.

What do you think about these for turning? https://www.waxracingproducts.com/collections/wax-racing-products/products/adjustable-billet-sponsons @waxhead installed them on his FX-1 @Aquaholic installed them on his Mini Monster 550sx.

Thank you. After I found the round top goes into the crank in the diagram, I actually saw that the groove in the crank itself had a round cup to receive it. Now I need to know if I have it seated properly. I will torque it to 50 foot pounds and then see if the cover fits, if you have any...

I scavenged and cleaned up both a functioning Bendix and Flywheel from another engine and now am trying to install the Flywheel onto the FX-1 crankshaft. Is the Woodruff Key installed Round Side up or down? Note: Although it doesn't show it in my FX-1 Service Manual it does show that the...

Putting in the bendix from the 650 now for now. Waiting for parts to come. Thank you guys!

Part #18:

Ding ! Ding ! Ding ! We have a Winner: @Storbeck You can seen the third piece of the bendix plate inside the bendix here: I have a spare 650 engine. Is it the same bendix as in the 701 61x? But I am a bum because I left the flywheel cover off and it has surface rust on it. Can I clean...

The magnet which is cracked. Can I just buy a new magnet? Or do I need to buy a new flywheel? If so any suggestions where and what to buy? There is too much oil in the stator area. What can I use to clean it? Brake Cleaner? Carb Cleaner? CRC Electrical Contact Cleaner? See another piece...

What is that piece of metal poking through the flywheel hole above? Here is a close up of it removed: The Cold Fusion Flywheel Holder for Yamaha is simply the best designed tool out there. The generic Ebay Flywheel Puller needs the three holes widened out to fit properly, but once done is also...

Ok, now I have my day planned. We want to ride again at 2:30 pm today. So I will get going now. Thanks buddy.

Thanks Mike. I can't remember, can I remove it once I take the cover off without pulling the flywheel?