Search results

Working on a relatives ported 701 round nose with a B pipe, head, VForce reeds, MSD CDI and stock 38's. He had several issues going on last year, he says it ran good, but it was lean at times and rich at times and plugs fouled a lot. He drained the gas out of the tank last fall and it's been...

Like the title says, it there a simple test to see if a running PWC is charging the battery like it should?

The Weldwood can says it takes 7 days to reach full strength. Do I need to wait 7 days before I put a ski with new turf in the water and use it?

Can you run 38"s with a aftermarket intake? If so, does running a aftermarket intake gain you anything if your running stock 38's. On say a ported 701 with a B-pipe, head, 180psi, VF 2's and a MSD CDI.

A stock Kawasaki 1100 head off a1996 ZXI. I used the engine in a SXR 1100 conversion, but I used a ADA head, so this one is up for sale. It's off a fresh water ski and is in great shape. Paypay only, $45 + $10 shipping .

**SOLD**For sale a nice set of stock Yamaha 38mm carbs. I've had these for several years as a spare set, but I'm cleaning out the garage. They are fresh water carbs off a Raider I believe, I bought them off a guy in KS parting out his ski. All the screws turn free. I took the covers off for...

I want to do some reinforcing between the tray and hull on our Rickter. The photos I've seen use 1" to 1.5" square carbon fiber tubes (carbon fiber ski) about 1/8" thick. I can find lots of thin round tubes and a few square tubes, but nothing that is 1/8" to 3/16" thick. Anyone know who sells...

We have a couple skis that have pod flame arrestors and they get too much water into the carbs. I need to fix this and find a way to keep water out of the carbs. Before someone asks, Yes hood seals are tight, no hull leaks and we have bilge pumps and big ball valves in the skis. These are...

We like a tight handle pole on our SJ, but I'm scared to tighten the stock bolt any more for fear of breaking off the ears of the stock pole bracket. I know they make special pinch bolts, but their kind of expensive. Can I just get rid of the stock bolt & spring and get two short ss bolts and...

Typical SJ, 701 with some porting, a B pipe, ADA girdled head, 180psi and stock 38's. Runs great, plugs look spot on, it starts instantly and idles great. But, put a couple hours on the plugs and it looses power. At first is like you have 90%, then 80%, and finally down to about 70%. It...

As the title says, it this setting advanced or retarded?

Dasa 1000, new pistons, rings and bore. Dasa did the work and all went together great, turns over fine and sounds normal turning over. For the heck of it I checked the compression (good gauge) before I put in the water and it's only 150!! It should be 180 - 185. I've never seen this before...

Not a huge deal, but it would be nice at times to remove the engine without removing the ebox. Would it work to cut and install Weather Pack connectors (Like new cars have) on the stator wires. A nice 4 wire waterproof connector would be nice to unplug at times.

Well I can't get the link to work. Northern Tool has a cargo carrier on sale for $40

08 SJ with a 701, mild porting, 180/180 compression, stock 38's and a B pipe with a flow control valve. When the valve opens it dumps a ton of water in the stinger, should I also run a restrictor in the line? I'm probably over thinking this, but with duel cooling is it possible to move water...

Finishing up final tuning on our 08 SJ makeover. Just a lake ski to play with, jump wakes and race around with friends. Runs great so far, getting ready to GPS it tomorrow. Curious what people think our top speed will be. Fresh 701 rec (mild) porting of cylinder and case ADA head, 35cc...

Like the title says, I added an RRP steering system w 50mm fat bars to my stock SJ handle pole. The stock chinpad could be made to fit with a lot of modification and recovering, but I'm wondering if anyone has the same setup and what chinpad you use?

Rather than buying a 120 jet for my water injection into the exhaust I'm going to drill out a smaller jet I have. Am I correct, to get a 120 size jet I need a #31 drill bit, it's between 1/8" and 7/64" ? Thanks

We have 2008 SJ, typical 62T/61X set-up, pipe, ported cyl , ADA head 180/180, V-Froce reeds with stock 38's. I have a set of Yamaha 44's off a 760 Venture and I could switch to them. We only do lake riding, playing around, jumping cruiser wakes and we go on long rides pretty often so fuel...

I'm going to replace the stock tray turf on our 08 SJ. We ride on flat water, but do jump large cruiser waves. I don't know much about under-mat foam padding, but sounds like it would be way more comfortable. Do you just glue it down first and then glue the turf to it? What thickness, I...