Search results

I am installing a Factory Limited B-Pipe on my 1995 FX-1 with the single carb oem SBN 44 carb and stock 61x engine with the oem head. And currently a MSD enhancer, but may move to a Zeel charging CDI in the future. The pump and the aluminum impeller are likely stock. Do you recommend that I...

1995 FX-1 with Single carb 701, MSD Enhancer, stock oem exhaust. Throttle cable is not hanging up. Runs fine at idle to slow ski-able speed but seems like there is no mid-rpm. Rather, the ski goes from slow but ski-able speed to 3/4 WOT. It runs fine at 3/4 WOT to WOT. There is absolutely...

RSKI riders has a surf ski super jet fiberglass reinforcement video which shows a laser cut chopped strand and S-glass kit for to reinforce a super jet hull. Does anyone know where I could get something like that? Or does anyone have a template which I could lay over my fabric to cut out the...

1994 Yamaha Square Nose Super Jet HIN No.: YAMA1937B494 PRI I.D.: GH7 0800726 Other than a new drive shaft, midshaft bearing any other parts I will need? I noticed that the pump was shimmed. Is there an alignment tool I should use?

1993 550x with reed engine. Interstate Battery, 12.79 DCV Starter switch causes (the starter solenoid?) to click/clunk, but no cranking by the starter whatsoever - not even an attempt to spin the engine. No humming, no sound, no nothing. 12.79 DCV at the starter solenoid-in post. 0 DCV at...

I have this on the fuel pickup in my FX1: Yesterday, the ski would die at WOT racing my wife. FX1Dave told me it was likely fuel delivery starvation at WOT. I started troubleshooting this morning from the tank to the carb and noticed dirt in the tank. The fuel pickup screen also seemed...

What engine is this?

What is the Best Ride Plate for the 2008+ (e.g. 2019) 2-Stroke Super Jet ?

What is the Best Intake Grate for the 2008+ (e.g., 2019) 2-Stroke Super Jet and for what water conditions and why?

This is my fourth installation of a MSD Enhancer in as many Yamaha skis. I always disconnect the positive cable from the battery. And I always blow the fuse in the Ebox. How I do that, I don't know. (Is the CDI a "capacitor" e.g., like the start/run capacitor in a home air conditioner...

Apparently the Factory B Pipe is different for the 61x single carb Super Jet and for the 62T dual carb Super Jet. How can you tell that if a B Pipe is for a 1996-2020 SJ700 Super Jet and not the 1993-1995 Super Jet?

I just bought a new to me 2019 stock Yamaha Super Jet: It definitely is easier to ride than my 1995 Yamaha FX-1. And I have no doubt that it will be a reliable ski. I have a MSD Enhancer still to put in and I have ordered a Blowsion Billet Handlepole. The ski rides very well. For instance...

I have read here that putting some padding under an aftermarket handlepole such as the Blowsion Billet Handlepole is advisable to protect your knee from steering plate injury. I see this one here and have asked the poster about it in a 10 year old thread: I think I remember a rectangular...

PSA: Please share with any liberals you know.

I read @TIMMAAY's recent thread on this subject. Apparently, @john zigler has a quick steer adapter plate: He said this about it in TIMMAAY's thread: Great video by John Zigler on how to install his quick steer kit (note you do not drill the pole, you merely drill the stock steering plate...

I have a 1993 Kawasaki 550sx with the reed engine and 180 psi compression in each cylinder. I would like to install the Waxracingproducts.com 550 Kawasaki Intake Manifold for SBN 38 carbs. And I have questions. JetManiac sells the single SBN 38 carbs for a great price, but they are single...

I scavenged and cleaned up both a functioning Bendix and Flywheel from another engine and now am trying to install the Flywheel onto the FX-1 crankshaft. Is the Woodruff Key installed Round Side up or down? Note: Although it doesn't show it in my FX-1 Service Manual it does show that the...

1995 FX1 with stock 61x engine. Yesterday it went from maybe every 1 in 10 starts to 5 to 7 in 10 times when I hit the start button the bendix would just whiz/spin but not engage the flywheel. Is the bendix spring broken? I can't remember, can I get the bendix out without removing the...