Search results

Ok so now it begins. I am starting on the sxr fixed steer hood. anyone have a good side picture of a new x2? I have some things I need to change from where the sj conversion was. measurements would be useful too. Here is the ski with a cutdown pole, I need to get some measurements of angles...

For me Daytona started and ended with Mark Gomez!! First one on the water sat morning and rolling and flipping everywhere and then finishing off the freeride on sunday with the races no less!! you sir are a madman!! I bow to your greatness. Obviously there was a lot of very cool things going...

Radney sent me some results from Havasu. 1. Manabu Matsudayashi 2. Dan Ashcroft 3. Naoya Hamanaka 4. Kazuaki Sakaida 5. Alexander Kuramsmin 6. Jack Moule 7. Lorin Lowe 8. Jared Ajoulny 9. Derick Kemintz Jr 10. Khaled Al Qubaisi 11. Bruno Jacob 12. Larry Sarinana 13. Vaclav Zacek...

I am making a lowered hood, chopped down, widened around the pole, slightly longer rear air intakes( but not long enough to mash my knees into-yeah if its possible I WILL smash into it) and also has the sides shaved to make hood tricks easier. I'm gonna be running an x-metal lowered bracket...

these are going to be 125 shipped. I have purposely left the front full so you can trim it up to your tastes. around the column, trim the hood, cut just a hole for cables, etc. it will mount thru the bottom and thru holes at the front it will use the original holes. making a shaved hood to...

predrill holes for sponsons, mix up some thickened epoxy and smear on like pnut butter. install and wipe away excess/ fill any small voids where the part is not flush(or you can spend a few more minutes and sand it perfect). by the way these are one of the very first sets I made and are not...

I am making a bottom front fill. you will apply some 5200 or thickened resin to bond the foam( much like a sponson(tubbie) and then a few layers of glass should be it. the green is a release chemical that I left on so you can see it better. still need a little sanding on the edge to fit flush...

What is the best/cheapest way to ship to Australia? I priced a box 60 x 8 x 8 that weighs 7 -10 lbs. the length is what kills it I think, but then again I have never shipped anything to Australia. my quote was just under 300.00!!!! yikes. might be cheaper to fly over and make parts and fly...

I landed pretty hard on my exhaust and busted the aluminum collar that holds the black nozzle to the hull. it still holds it on but not for long. Blowsion sells a nice ring to replace it- but I can't get the thing out of the hull. Before I go and break it into a million pieces can someone...

I am about to redo my footholds and refoam mainly because I hate my footholds and how the turf took most of the room out of em. I refuse to put 25mm pad in and then sand it down to 5mm. so I made something I can get my foot into with room to have 25mm pad and turf on the bottom AND turf on...

just saw this on pwc. what next a 20' Sea Ray? YouTube - Ozfreeride.com Boat Harbour 6-7-08 Jetski Freestyle

its a blaster II motor in a B1. recent purchase( not mine), had some starting issues and got a new stator as the pulsar coil was thought to be bad. no fix. so now I get it. have taken the front cover off to check the ground, and resanded where someone else had already. also the other end of...

Its been semi-secret that myself and Wavedemon teamed up to make a new roundnose superjet conversion hood. well we have agreed its close enough to share our little project. We asked a few riders in our group about some design elements and I would like to thank them for their opinions- Thank...

Is that a grey hair I see???? :haha:

has anyone experienced a bad stator on their sxr? Or one that was starting to go. what were your symptoms????

I know this has been done before but I am taking a whack at it. I have help, but I need more. I want to make a magazine for standups. it will have to include all watercraft because the people who pay for advertising mostly won't be standup specific businesses. but I can still have...

sxr-hood problems??? ok ski has a factory wetpipe and the air horns removed per instructions. its an 06 low hours, has siphon and rule bilge working. the hood hoses are cut shorter to accomodate the pipe. on flat water runs fine all day, within 20 minutes in the small surf in daytona today...

seems like tubbies are big now and guys are wanting correct fitting tubbies for x-2's so here ya go. 200 shipped. gelcoated and foam filled.

Hey guys- second time riding an x-2 yesterday. I picked one up after seeing D-slicker and Pete just tear it up at Daytona last year. So I just got it up and running yesteday and took it to the water. its got a 750- the small pin I think ( has the two extra intake holes) single carb keihin out...

Twist grafix made some awesome stickers for my shop! thanks Ollie. hand delivered and fixed some wiring in under 10 minutes too. I am now in your debt.