waxhead's latest activity
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.Youa re talkinag about water control and yes I thought about this a lot years ago. I used to worry about it a lot but it never seemed to...
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.www.zeeltronic.com https://www.waxracingproducts.com/pages/zeeltronic-curves
-
Wwaxhead reacted to fastgtfairlane's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with
Like.
You can change settings on the zeel cdis as long as you have the proper programming cable. You can download the software on Zeeltronic... -
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.Do you have an msd enhancer ?? if you do then sure. The zeel is a bolt in and it comes with the wax v3 in it
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.Good point. i mean its the easier way if you dont want to machine. the bad thing is you are dropping the transfers down as well as the...
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.ok i would go for a 2.3 n/s 90 gram spring 140 low and a 120 high this would be my starting setup
-
Wwaxhead reacted to MarkWalker's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
Did anybody check with SUPERJET-113 to see if makes the 0.010 base gaskets?
-
Wwaxhead reacted to E350's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
On an unrelated note . . . Eureka!!! Along with my @SUPERJET-113 gaskets too!
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.Yup i have done that before, on stroker motors when you need to get the timing lower, bascally pretty much any stroker motor using an...
-
Wwaxhead reacted to WFO Speedracer's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
Or you can use the old Kawi 650 trick and just 1211 the cylinder to the cases , no gasket, I have been running my 650's that way for...
-
Wwaxhead reacted to E350's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
So, checking for understanding. Just to be clear, for 46mm carbs, you prefer aftermarket Mikuni 46 SBN carbs, correct?
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.https://showtimefreestyle.com/en-au/products/mikuni-dual-carburetors-46mm-performance-package
-
Wwaxhead replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.You’re talking about I-body carbs there—they’re really just emission carbs and best avoided unless you’re in the alloy scrap business...
-
WSorry for all the LSP doubters!!! I had a minor part failure on my S1. I contacted HSI, which told me warranties are direct with LSP. I...
-
Wwaxhead reacted to fastgtfairlane's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
i agree and wish i wouldve gotten the 46s instead of the 44s when i bought them. im also very curious of how your manifold compares to...