Search results

Filters have never been used, steering nozle excelent shape and pancake pete never used. Call or text w questions. I rarely check pm. 978 771 5439 Pancake 50 bucks including shipping Nozzle 50 including shipping Filters 25 each including shipping

Have a superjet fuel cell I used on my rickter in great condition and my old motor ADA Billet 920 cylinder and head. See pics, lost one cylinder from detonation. This happened several yrs ago. Just found the motor in basement. The rod went through the bottom end. Will need new domes etc...

Never installed and never used. $25 plus shipping

The tank is brand new, never used, never installed. Its for the tank only $250 + shipping. Feel free to call or text 978 771 5439

2014 Full Visual Carbon FS2 Evo 701 61x bore and ported by Nuklear with pro x pistons. 61x cases with SBT crank B Pipe Limited New ADA head with 34cc domes Wet Jet intake with 46mm Carb Mint electronics with everything OCD solutions makes and MSD enhancer Zero drilled and lightened flywheel...

Bought Robby's Rickter FS2 from him this week. The ski was exactly like as he advertised. His crating and shipping skills were the best I have ever seen. Highly recommend him and will do business again. Thanks Captain!!

I want to paint the belly of my Rickter. The paint and sticker that Rickter puts is brittle but some areas are on like cement. Any tricks to this? thanks

I like zero play in my throttle lever but Ive been noticing the rpms will go up alittle when I turn my bars. I thought if I shortened my pole for added cable slack it would fix the problem but it didn't. Is there suppose to be some play in the throttle lever? I then loosened the cable...

Im running a Rickter FS2 Hull. Whats the measurement range the shaft can stick out of the housing as seen in the pic for a Rickter FS2? I noticed a little play in the mid shaft when bolted to fire wall but not attached to motor so I pressed the shaft in another couple mm and the play...

I tried a front strap and due to my front foot always being in different positions Im thinking of trying a front foothold. Whats everyone running for front footholds? I liked the Tomski but dont think they make them any more? thanks, Peter

Ive read many articles not to run synthetic two stroke oil in a new motor in order for it to break in properly. I believe the rings will not seat properly etc. Anyhow, how long should you run a new motor with non synthetic before switching over to fully synthetic for the advantages of a fully...

Ski is acting crazy. When I go wide open throttle the power comes and goes while the throttle is held open. Its just nuts. Sometimes the ski wouldnt even turn over it was just totally dead as if someone took the cables off the battery. Then alittle later it would start but would have the...

Just got a brand new set of 49 mm Full Spectrums. Looking for info on how to install primer? Do I drill into the carbs, one of both, and where? Thanks Peter

Did a search but couldnt find much. I have Rickter with rear footholds. I finally decided to install a front foot strap over foothold but now Im thinking of installing another foot strap in the rear instead of using the rear foothold. Does this make sense? hats everyone else doing with the...

My Power Valves are hitting the exhaust manifold and preventing them from opening all the way. Looks like on of the bolts holding the right PV in is also hitting the exhaust manifold which is preventing it from siting straight on the motor. Not sure if there is a spacer someone makes that I...

Anyone have any instruction on power valve removal and any torque specs on putting it back on? I cant get a wrench on either of the two upper middle bolts to insert the Exhaust manifold. If I could take the Power Valve off I could get to the bolt and tighten it then re install the PV but wasnt...

Where can I find the studs (think there are 4) that go into the engine case and holds the intake in with lock nuts? Or what size are they, maybe I can buy them online? Thanks Peter

I guess its time for a rebuild, lol. Rod snapped and went through the case by the starter and through the bottom. Looks like the top ring is fused to the piston. Top of piston looks a mess. Trying to figure out the exact sequence

Have fun and be safe, Anyone riding today? Peter

Looking for some starting points for jetting and prop? Im installing a DASA 1100 - 10 mil motor. I will be hooking my 48 mm full spectrums up. I am currently running a 14-19 prop and 144 mag pump. Im from Mass, water temp is currently around 46 degrees only ride in the ocean. Ill be running...