Search results

I am having an issue with my 2008 SXR 800. I recently changed the steering cable and for some reason now the engine wont go above idle when it is in the water? It runs fine and pulls RPM on the trailer but anytime it is in the water it fails to go above idle. It has a wetpipe installed as well...

So I recently replaced the steering cable on my 2008 SXR and now the motor is not reaching rpm. I have dual cooling installed on the pump and had to change the angle of one of the fittings off of the pump and am wondering if that could effect it as it has a wet pipe on it. It is hard to diagnose...

I have an 08 SXR it has a wetpipe on it so i have removed the factory temperature sensor and just siliconed the connection and electrical taped it also has the 6 degree timing advance . It also has a Bildge pump installed. I am just stating this to let you guy know about any changes i have done...

Does anyone know where i can find one of those shirts i can't even find a pic of it. But i seen it at the Surf Slam a couple years ago it was a red shirt with a sit-down with a cancel sign through it, along with a funny saying.

I ordered a new set of domes from blowsion and since i installed them my machine is running rough i lost 700 rpm i used to hit 7000-7100 rpms and now i am only getting 6200-6300 my old domes were 29 cc and i was getting 160 psi and now my new domes are 27cc and im getting 190 psi im running 94...

what should my pop off pressure be i have a set of novi 48's

So i know i habe an airleak caused by the uncontrolable revving of my motor if i have 190 psi in both cylinders it means that the head cant be leakin righ and it has to be on the intake side of things i did notice when i pumped the primer lots fuel came out of the end of the shaft for the...

will my jets outta my stock carbs fit in my new novi 48's since they are both just a mikuni body anyway.

Wondering if anyone has a favorite jetski scene from a movie like old school waterworld haha post em up!

so i purchased a set of novi 48's, r&d manifold, v force 3 reeds and a tbm angled reed spacer for my ski and was wondering should i use the reeed stuffers for the reeds or because the intake is supposed to be a matched system with the v force reeds should i leave them out thanks!

I checked my compression and i got 160 in back and 150 in front is that normal or should i look into new rings? Its on a 2008 sxr btw

Hey so i have a jsu girdled head and im running 29 cc domes and im only getting 150-160 compression so i wanna try some 27 cc domes but cant seem to find them anywhere does JSU no longer make this head or replacement domes?!?!?!?

So last season i was pulling 7100 to 7200 rpm now this year i did change my impellar to a solas dynafly but even at the start of this year i was pulling 6900 rpm then i lost some more rpm somehow and was pulling 6700-6600 and now im down to 6200-6400 rpm what could be causing this ive played...

So last season i was pulling 7100 to 7200 rpm now this year i did change my impellar to a solas dynafly but even at the start of this year i was pulling 6900 rpm then i lost some more rpm somehow and was pulling 6700-6600 and now im down to 6200-6400 rpm what could be causing this ive played...

Hey what kinda carbs are you guys running? I recently purchased a rd intake and v force 3 reeds and a list of my other mods are wet pipe,timing advance, jsu girdled head, dual cooling, 80 mm nozzle, 14/22 solas dynafly, im not sure what size either 46mm or 48mm and either novi's or mikuni's. Im...

last night i was installing a new battery into my waverunner and as i made the final connection on the ground is sparked (as expected) and then my ebox starting smoking and I could smell burning (unexpected) i pulled my ebox apart and it was melted i was wondering what could have caused this any...

do most of you guys just use contact cement for turfing or is there a better product out there for use

im just getting my ski out of the garage after another lame canadian winter and i notice the bars are hard to turn side to side and they make a grinding noise is there a point i should lubricate or is this signs of a steering cable about to go or should it go away once i start riding this summer...

I have a couple questions on the flow of the cooling water correct me if im wrong. I am also running a factory wetpipe and jsu head. The water comes from the pump to the the east side of the ski assuming that the bow(nose) is north. it then comes into the engine bay on the west side and connects...

where does the second waterline for a dual cooling set up come into the engine compartment. on the instructions it says it is used for a drain on the overheat sensor on the stock pipe i now have a factory pipe and i cannot see where it comes in apperantly somehwere on the bulk head? Also does...