Search results

All parts are fresh water only. Prices do not include shipping nor pp fees. Make any reasonable offers! • Stock SXR800 flywheel - sold • Stock SXR800 head - sold • Stock SXR800 finger throttle - sold • West coast 750/800 exhaust mani. Ported by RadDudes for factory head pipe. Setup for dual...

Moved from Phoenix, AZ to Portland, OR area last year and am ready to get riding again. I am looking to get with a group of locals to ride with and learn the area. I am also dying to learn to ride surf. Let me know.

Just finished putting a blown up chicken together. It has 650 with a coffman pipe and a 38 CDKII carb. The ski starts on the trailer and revs good. I left it on the trailer on the ramp to get the low speed circuit and idle dialed in. It is hard to start when in the water and will only stay...

I know there are a few of you out there with SC's. I have never hooked up a Coffman exhaust and can't find much through searching. I am confused with what to do with the third fitting on the headpipe. From what I gathered, the outlet on the head goes to the top of the headpipe. The...

Been looking around for aftermarket hulls available to fit a SXR power plant and pump. I remember seeing these here and there but they are not too common. Apparently they can make a SXR based light weight hull. You can go as low as 75#. Anyone around here ever run one of these hulls and is...

For all that is running a Xmetal pole on the sxr, what steering setup are you running? I have a new pole on it's way to me and don't know if my current R&D turn plate will work this this new pole. I asked Xmetal but they were unsure and did not know about the R&D turn plate specs.

Just looking to gain some more knowledge on this. I do know that most engine builders do this mod when they port and engine and such. I was also told that it makes carbs easier to tune since one carb is now feeding one cylinder. Any other benefits to doing this? Is this mod better for a...

Was wondering if anyone has installed a versi-plug below the exhaust outlet on an SXR or Superjet? I have noticed that the hull will fill with water in the right gunwhale side and has no way to drain except for the small hole in the bulkhead behind the stock siphon bilge block. I was maybe...

Looking for some pics and info on running a X2 trim setup on a SXR. I believe SXR-Forever had done this and was looking to see if more people had followed. Any problems with the currently running systems out there?

Nothing really special here. Just some good scenery and a few animals. There was no big boats cruising around. It was F%#&*^ hot that day!! http://www.vimeo.com/13074463

The past few months I have been noticing that the ski will not hit while in a tail stand nor if it is laid over on the port side (carb side down). It just tends to load up and will not clear out. It did this last season, but then cleared up early on this season. I first thought that maybe I...

Can anyone recommend a steering cable lube kit? Mine steering is feeling quite sticky lately and wanted to give her some lube.

Currently running ADA head with 28cc domes (175psi), lightened flywheel, light bottom end porting, 80mm nozzell, TBM pump stuffer with stubby cone, wetpipe with timing jumper, and a 13/22 -5mm Solas Dynafly. The ski hits pretty dam hard on the bottom and pulls all the way though to the top...

Well I have been riding the piss out of this SXR for the past two years. I have at least 200 hours clocked on it without an issue. I rode through most of the winter but decided that I need to take care of a couple of things and add a few before the fun time gets here. Here is a list of...

I am doing a spring freshen up on the ski right now and am going to install a second cooling line for my wetpipe since my rear overboard pipe is not used. What size of fitting is recommended to secure to the pump. I was thinking of just using what factory pipe sends with the wetpipe. 1/4" NPT...

It seems that there are a ton of questions, ideas, ways to mount cameras and such while riding. Most are posted sporadically in different threads. I figured we would start one just for this purpose where people can share different mounts, tethers, flotation, etc. I use a GoPro wide. I have...

Ordered a few of his custom SST pissers. Communication was spot on and shipped when stated. Product looks great. Thanks!!

I was just minding my own business last weekend and ran across a garage sale in my neighborhood. Well they just happened to have a running pit bike for $100. Figured I could have fun with it. It does need some work but like I stated above I know nothing about these. Only messed with cars and...

How high of compression can I go with a SXR modded with the FFP wetpipe, 6 degree timing advance jumper, and stock ignition before the advance is to much and deto occures? Right now I am at 150# per cylinder and was thinking of bumping up to around 170-180. If I cannot go up this high, will...

I have been searching a bunch of threads and read about some irregularities with compression stated on ADA website vs. actual compression. I am getting ready to install the girdled head on my SXR. Currently the only other engine mods are aftermarket arrestors and a wetpipe with 6 degree...