Search results

Like title says - looking for the two black plastic trim pieces at the back corners of the rail/tray. Must be black not purple. PM me if you have a set. Interested in paying cash or trade for a set of fiberglass footholds.

I have a good running 2003 66e 800 PV engine. This is a complete ski but the mid shaft carrier or drive shaft splines are stripped. Engine runs strong but impeller and drive shaft not turning. Happened yesterday 7/18 out of the blue. I have too many projects and no time to fix, but thought to...

I am putting footholds in my '08 superjet. I picked up a roll of black diamond turf and was planning on re-using the stock black rail caps and turfing below them and in the tray. I have the footholds all glassed in and am ready to turf at this point. What are you guys using to re-glue...

Looking for some help with this. 62t case 61x rec ported cyl dual oem 38's stock flame arrestor stock head When I looked on factory pipe's web site they recommend the following for the blaster 701 mod pipe... 140 Main 1 1/8 70 Pilot 7/8 Needle/seat/spring - stock (55 psi)...

Some pictures from 2007 of my buddy bare-footing behind my 650 sj. He starts out on a knee board and then stands up once we're up on plane dropping the knee board. It took quite a bit of practice to master this. Disclaimer: Yes this is far from legal however we always have a ski boat...

Took these pictures at work last week; was out inspecting this bridge and taking a look at the columns of the approach spans when I found this gem. Each column had a sports action figure mural painted on it... RT 1 over the Schuylkill River, Philadelphia PA. I love the plume of black smoke...

I tried searching and the Tech FAQ but all I found was stuff for Riva and ADA heads.... Can anyone point me in the right direction on O-rings for a Pro-tec C2 head (seen below) besides buying the $30 kit from Pro-tec... Thanks.

I know a few of you have used this to paint your skis. I am looking to paint my sn and rn this year. I am planning on using Interlux Perfection (top deck) paint. Today I called the manufacturer to ask for a recommendation from them on a primer and other prep tricks. Basically the...

Never seen this before, bridge port 701 cylinder... http://cgi.ebay.com/ebaymotors/Yamaha-701-Bridgeport-cyl-with-New-82mm-pistons_W0QQcmdZViewItemQQcategoryZ56422QQihZ004QQitemZ140201247615QQrdZ1QQsspagenameZWDVW

Were is everyone getting paint? Online? Local shops? How much (base & clear) should I expect to use on a ski (my first time)? Ive got 2 superjets that I will be doing. Any other recommendations on specific paint products are welcome, I used the TechFAQ and am pretty set on how to prep...

Ive got a single carb (61x case) 701 motor and have both an aftermarket mikuni 44mm or a wetjet 46mm carb available to use (minus the wetjet manifold). The motor will have the usual basic mods (b-pipe, some porting and maybe some compression) Who has run the 46mm mikuni on the x cases (non...

Both of these skis are in need of quite a bit of work. I acquired them both in the last year with plans of major overhaul in the winter and here I am... 96 RN This skis been through some serious abuse. Its cracked at several locations mostly resulting from a drypipe bouncing around at the...

Well I'm de-foaming my 96' superjet. This hull has been around the block quite a bit. I acquired it this summer and rode it to the end of the year as is knowing full well it needed serious help. It even listed to one side severely when just floating. There were several water infiltration...

How do you when its time for a new or rebuilt crank. I have one with very faint noise in two of the bearings. It's certainly not chatter but it is audible. The other 2 are dead quiet. I was thinking of replacing the needle bearings and running it. In my experience its the needle bearings that...

Does anyone know... Is it possible to fit a B-pipe manufactured for the Kawasaki 650 or 750 into a yamaha superjet? Only problem I can see is the stinger cone not fitting with the yamaha gas tank. Anyone tried this? First pic is 650sx/x2 Second pic is 701 lim chamber I realize the chamber is...

My prop is binding on the wear ring in a few spots due to swelling of the wear ring. The pump is still good, was rebuilt this winter so I dont want to trash it plus its been blue printed. I read something in the manual about having it bored out to an oversize and having a new ring pressed...

Anyone ever hear of this? I aquired an MS DOS version of this program (freeware) I haven't gotten into it much really as I have finals this week but Im going to try to put something together to experiment with a yami 650 motor I have... It basically allows you to input all the specs of...

This may have popped up before, I dunno :dunno: but I though I would share. There is some killer 550 footage in here of Randy Laine. http://video.google.com/videoplay?docid=2796752983755999881

I need some padding for under my turf and I dont feel like paying $60 a roll or whatever it is from HT... I know Ive heard others talking about using some of the camping pads. I found this on Dicks website... So I guess my question is, is this the same type of foam as the stuff that HT is...

Anyone got any tricks for removing the coupler from the midshaft? I know the rag in a cylinder trick works great for the coupler on the crank... but thats not gonna help me with the one on the midshaft. thanks in advance, Aaron