Search results

I have a rebuilt 701, new old stock cases from Riva. I think I bought the cases in 08 The crank is used with about 100-125hrs all bearings and rods are in great shape. Cylinder is from a 2010SJ honed and still at 81mm. Pistons are new and have a coating on them. Head is a 61x was hot tanked and...

Looking at switching out my AC pole and I’m needing a round nose to square pole bracket. Thanks in advance

Looking for a D cut ride plate or any other freestyle for a Square Nose. Not interested in a stock D cut. I currently have Wamiltons that’s running a little thin from all the years of use. Just seeing what I can find before ordering a new Blowsion D cut. Thanks in advance.

Looking for a decent set of jugs for a 1100 63m motor. I will be boring them to 83mm so they don’t have to be mint! Thanks

My motor has an issue, like it’s starving for fuel, idling rough almost like a car with a cam in it. It’s pretty much a stock 1100 only thing done is a complete top end rebuild with 83mm wiseco pistons all new gaskets and fuel pump. Carbs were not rebuild and crank seals not replaced! The motor...

Dumb question maybe, but do blowsion domes fit ADA heads? I have 33cc domes but want 37cc

Chris did me a huge favor, mad props to this guy for all his help. So I bought a motor off a guy that wouldn’t ship it, Chris lives in the area! He picked the motor up broke it down for shipping and sent it my way. Note this was a complete Yamaha 1100 ebox to exhaust. Shipped the motor in tote...

Looking for 2 throttle drums prefer the 10 or 12 hole drums. Thanks

Looking for somebody in the are to pick up a motor for me package and ship it! I’ll pay you $125 to pick it up and box it and drop it at UPS or Fedex! And yes I’m paying the shipping also

Ok so to make a long story short, I got 2 new cases from Wamiltons on a deal! But they are just the cases no pins. I need the pins that hold the crank in place!

Just wondering if anybody has polished the inside of their cases? Is it helpful? Is there a drawback? Or just a waste of time? My season on this ski is over, just looking to do some mods for next season. It’s already ported and epoxied and finger ramps filled.

Anybody know where I can get replacement domes for my old Riva Yamaha head? I’d like 81/82mm domes at 35cc

Looking for flywheel and dual pickup, I have the multichannel 42351

I’m looking for somebody that does a good porting job or has an already ported 61x cylinder. I’m running this for freestyle. I have ported and epoxied 62t cases, oem crank, blowsion head 35cc domes, B pipe, Vforce 2 reeds, dual 48 blackjacks, tdr waterbox(stock cracked) MSD TL

Is the FX1 tail cone same as the Superjet? Lost my tail cone this weekend I have an extra tbm For a Superjet appears to fit but will I have problems with it? Thanks for any help!

Anybody have any tips to check for cracks on cases, cylinders and exhaust pipes? I’m getting water in the bottom of my crank case!!

Looking for a Square Nose aftermarket waterbox

So I looked through to about page 28 and did a search on here, no real results! But my question is what pipes will fit in a FX1 with a 61x? I know Factory made a Bpipe, but were other pipes made for it? I believe I’ve also seen a Type 9 squeezed in 1. Thanks for any help guys

Looking for a good used aftermarket pipe that fits in a Square Nose. Nothing too modded! I have a 62t girdlled head 38cc domes epoxied case dual 44 blackjacks nothing major done.

Just wanted to say thanks for having me here! I was a member in 2003-2009. I’ve been out of stand ups for a while but getting back into it. My 3 kids are old enough and it’s time to teach them! Side note pulled out my old 1990 RN still looks like new under the hood fresh gas started right up...