Search results

This chamber is rough, but that is reflected in the price. That being said, I am sure it will perform just fine. It has a few rough spots, the worst being in the last picture. The divot does not go all the way through, but I would probably fill it anyway. Measures approx. 25 ½” long, which I...

Both are in good used condition. Asking $50 Shipped each in continental U.S.

This came with a mag pump I bought for my Blaster. The seller said it fit 1990 – 2007 SJ. It measures just over 26 inches overall. The bearings turn smooth and I would say they could be used again, but that is up to you. The pump it came out of is very nice, so I don’t think it had a lot of...

I have a 9/15 hooker, with the stanard finish, that I am going to put in my B1, with a Solas Mag pump. I have everything I would need to polish it. Just wondering if it is worth the time and effort. Thanks, JJ

Just womndering if anybody has experience with these. Pretty pricey, but would be good if they do what it says. https://www.superflypro.com/shop#!/Flex-Fins-Blaster/p/62418788/category=116676628

I was going to piece together a B-Pipe for my blaster, but I found a complete pipe. So, I am selling the manifold I picked up separately. Not the best or worst casting I have seen. Does have some voids, but should seal up fine. It was advertised as Super jet/Blaster manifold, but the holes are...

Just picked up a Pro-Tec pipe and head for the Raider I am building. Just wondering if there are still any half girdle kits out there. Thanks, JJ

Only need one, but would buy a pair if priced right. Just need the cage (as shown in the attached pics). I have reeds and hardware. Thanks, JJ

So, I bought a b-pipe because I needed the manifold and headpipe for my Blaster. It came with this fugly chamber, which I don’t need. I think it is a mod chamber, based on the length (approx. 25 ½”). It has a place where it has been patched with jb weld (or something) that I would work on if I...

Setup for dual cooling. It includes a rebuild kit, which has new gaskets, bushings, coupler, bolts, and installation instructions ($165+ shipping from Pro-Tec). The manifold to cylinder bolt holes have been drilled to 10mm (was not told when I bought), but I have four 8mm ID-10mm OD spacers to...

Just wondering if anybody has used one on these, and if it worked well?

I have some parts to sell. Mostly Yamaha, except Kawi X2 trim pieces. Prices are OBO for shipping in continental US. 95’ or 96’? Waveblaster seat trim pieces W/mounting screws - $50 shipped OEM Waveraider splash guards with mounting hardware - $50 shipped Yamaha 62T 38mm intake manifold &...

For Yamaha 61X/62T. I Know, a lot of people looking for these, but thought I would try anyway. Would also be interested in a WB1 mod chamber. Have my name on the TNT list, but who knows if/when that will happen. Thanks, JJ

So, still going to work on piecing together a b-pipe over the winter, but I picked up a Pro-Tec pipe for a good price. I figure it will add a little more brapp for now anyway. It came with all of the gromets, the triangle bracket and the long manifold bolt. I have read a lot about the advantages...

The WB1 I just picked up has a top loader intake grate, and a stock ride plate. Looking around, aftermarket ride plate prices have gotten riduclous (Iike everything else). I saw a Rend Engineering ride plate on flebay for less than $100, but I could not find any reviews. Anyone on here have...

Hi all, I sold my last B1 about 4 years ago, and have regetted it ever since. So, I am looking at buy another one. The only choices, near enough, are: 1. 1995 with 62T/61X motor, stock pipe, dual 38mm carbs, west coast head (non-girdled), and a few other AM parts. 2. 1994 with 61X motor, 44 mm...

The ski runs good. I had it out on the lake on July 28, 2023. As far as I know, the motor is stock, except for a 42mm Keihin racing carburetor. Compression is just over 130 PSI in both cylinders (Which is not bad at 6,000 feet above sea level). It has an Ocean Pro ride plate and an aftermarket...

I bought these for a project, but I sold the ski and have lost interest in repairing them. One carb has a damaged throttle plate, which will need to be replaced. I think it will have to be cut out somehow. I bought a replacement kit that will be included. I took the carbs apart, and they look...

I picked up a cheap X2 that had been sitting outside for some time. So, the seat cover is dry rotted. I am thinking about having it recovered and doing a tall seat. But I thought I would check to see if anyone had one they wanted to sell. I can do an exchange for my old seat + $ or buy outright...

This motor has been in storage several years. I bought it to put in my blaster while I had the motor that was in it built. That never happened, and I had to sell the blaster. So, I never ran this motor. The cylinder walls look good, and it turns over smooth and quiet. Since it has been sitting...