Search results

Good afternoon all, I'm looking for replacement aluminum tubes that go inside the KP pole. I see the RRP ones on blowsion are around $50 each... anyone know of a vendor that has ones that aren't RRP? Maybe a tad cheaper?

Hey all, I was doing a leak down test today after installing some new crank seals. I noticed the pressure would drop pretty fast so I knew I had a leak somewhere post installation. Found this spot with a soap/water spray. Motor is an ET1107 These are 62t cases that have been ported and have...

Hey All, I am attempting to install a Superjet Blowsion HD steering cable with the 6mm ends into my Superfreak circus. I am having some problems getting it into the pump side and shove it through to my pole. The HD cable side by side to my standard 5mm SBT cable is thicker at the crimp ends...

New in box, never used 9.5 liter Kart tank. Includes all hardware shipped with. 11 1/2" tall x 8 1/2" wide at the base and 9" deep at the base. $60 + shipping and pp fees.

Hi all, I'm looking for a set of high compression domes for ET 1107. The ones I have are stock and only hit 150 PSI at 7k foot elevation. Anything 200 PSI+ at sea level should get me to 170+ up here in the mountains. Let me know what you have! PayPal ready.

Beautiful 144 Solas Supra 14/19 used for 1 season. Stamp shows YB-SC-C. $75 OBO shipped to lower 48.

1 gallon capacity tank. Mounts to the firewall above the drive shaft. Has 2 outputs and 2 returns. No leaks, clean on the insides. Used for a few seasons. $135 OBO shipped to lower 48.

Can an ET 1107 be ran with single cooling? Does the motor produce enough heat to NEED dual cooling from two separate lines from the pump or can I use 1 in line from the pump and split that? Sorry for the stupid question!

WTB - intake manifold with Vforce2 reeds for ET1107. Shipping to AZ 86004.

Hey All, Does anyone happen to know what this nut size and pitch is on a oem yamaha starter? I managed to lose mine during a build and can't seem to locate the details on this little guy.

I have a SOLAS YB-SC-C Prop for sale. Not sure on pitch. It's in decent shape except for one small ding. I took a picture to show close up that the ding does not affect the prop's performance as it's only a scratch deep and not throughout the fin. $40 takes it. Buyer pays PP fees and shipping.

Hey all, I've got a OEM Yamaha 155 Reduction Nozzle with an unknown trim ring. Not much use for it. I believe the reduction nozzle is the kind with the 5 degree tilt. The trim ring came from somewhere, I can't remember. It had the b-pipe coupler mod on it, so it's got some gunk to clean off...

SOLD - PLEASE REMOVE - I have a beautiful vinyl chin pad with nice soft padding underneath. This thing is in excellent condition. No rips or tears anywhere in the fabric. This was taken off a RRP cast pole that did not have a steering stop. I'm pretty sure this chin pad would fit any Yamaha...

Hey All, Looking for a reduction nozzle for the 155 size pump that has an inner diameter of 90mm or more. Let me know what you have, paypal and shipping fees ready.

Hey Fellow Riders, I'm looking for a reduction nozzle for the 155 size pump that has been bored out past 90mm. Please let me know if you've got one :)

Couple things for sale... SOLD - Yamaha Factory Bpipe: Complete Setup - $650 SOLD - Custom Waterbox, no baffles - $50 SOLD - H20 Designs Fuel Tank - $100 Buyer pays shipping fees, paypal gift only. Bpipe is painted engine enamel blue. All screws turn if you break the paint. I tuned them them...