Search results

Need a WR500 sbn carb for a Kawi 300. Thanks

Looking for a 300sx tank or Kart tank that's not too expensive. Thanks

Troubleshooting my 750 small pin. No spark/no start. When I let off the starter I get a couple flickers of spark. This is using a second set of plugs (one set in cylinder, on set in the plug caps grounded to head.) If I remove the plugs from the cylinders (plug holes open) and crank, I get good...

Don't need this since I decided to part out my ski. These are from Superjet-113 here on the forum. For a 62T cased 701 and includes the gasket for a B pipe. I paid $122 shipped for this kit plus $20 for the Yamabond at my local dealer. Looking get $120 for the whole set shipped.

Removed for now.

Will get pics soon. Newmiller machine 701 milled head. 175psi, use with fresh 91/93 pump gas. $100 shipped

Will get pics soon. Came out of my personal ski. SOLD... 62T cases with cover and motor mount plates with bolts. $150 shipped SOLD ***** OEM starter and Bendix $150 shipped Core 62t cylinder $75 shipped Core Crank $75 shipped

Worx Dominator ride Plate 1990-2007 SOLD Worx Top Loader with bolts SOLD TDR water box (had this in both a square and a RN) SOLD

Selling a set of dual 38's. Rebuilt two seasons ago with genuine Mikuni parts including new needle seats and jets. Has carbon tech reeds. Jetted spot on for sea level using a Bpipe. Also includes a billet throttle wheel. $275 shipped

Complete 61x electrical. Has a MSD ignition.. Flywheel was done by Newmiller Machine. $950 $750 $550 shipped

Selling B Pipe, mod chamber. Mating surfaces are perfect, no pitting. All screws are free. Includes coupler, header bolts and turbo bands. Pipe has some goo on it from protective turf sections being Weld wooded on. Has two rubb spots. And yes, as you can tell by the sticker, it's the low...

Selling a complete 144mag. Fits 1990-2007. 12 vane Solas stator, Impros stubby cone, Impros 10/16 Hooker, Protec +60mm nozzle, trim ready, OEM reduction nozzle, wear ring and driveshaft. $900 shipped.

So I am swapping a mag pump in my bob from a stock stator, set setup is odd already. Currently had a 08+ driveshaft with a gp1200 or gp760 midshaft. I forget which midshaft but it is the really short one with the splines all the way up front. With the stock stator the drive shaft bottoms out on...

Selling my Superjet hull. Rear crank seal came out and the engine went poopoo. Don't have time or funds to rebuild. This ski build is two seasons old so everything else is plenty fresh. This ski was really fast and had no problem keeping up with my wife's STX-15f at full throttle. Selling a...

I haven't set up a pump in years. I pulled a stock stator pump out of my bob and replaced it with a Solas 144 mag. My old pump had an 08+ big hub OEM SJ impeller which I am reusing. The old stator needed a 2mm spacer for the impeller not to contact the veins. On the new pump I left off the...

As the title says for my trim cable. Thanks

Switched to a mag pump and no longer need this. Really nice stator, no chips, cracks or damage. Set up for dual cooling. Can also be used as single cooling if you install a 1/4npt plug. Includes a Blowsion stubby cone. Grease seals are still in, they have one season of use. Painted Kawasaki...

In good condition, just switching to Thrust as I like their lever feel better. Anodizing is faded from the AZ sun (not stored outdoors, the sun is evil out here). $75 shipped.

I bought this to use with my dual Black Jack carbs ony 750, unfortunately I can't use dual carbs with my hull setup. Selling this manifold for $150 shipped. Intake bore is 48mm but will work with 44/46/48/49 carbs.

As the title says, anyone have this setup? I got a set of BJ 44's for my 750 powered Hurricane Gen 3. Running a Sizzler pipe, milled head and flywheel, hooked to a Solas 144 mag pump with stock SJ big hub impeller. I got jetting from Jetworks, but they are sparse on the convo. Wondering what...