Search results

Dslicker recently sold me his XFT hood & nose. it was exactly as he described, i knew exactly what to expect upon reciving it, he shipped it when he said he would and emailed me a tracking number. packaging was perfect. i would definatly buy from him again. thanks for the great deal!

I just got my hands on a sweet XFT hood and nose. i was going to run my stock shortened pole with it... i mocked it up and it looks like the pole is going to stick above the hood and look funny. anyone else run a stocker like this? got pics?

so im installing my MSD in my blaster. i notice i have an extra green wire. i look at a FAQ (some great info) then i look at my ebox. DUH! there are 3 connecotors on it, 2 for the start stop switch and that extra one... its got 4 wires in it, one is green, (thats my extra...

i have searched, seems like sxr threads die off real quick around here these days... haha! my buddy has and 03 SXR, wet pipe and stock head. were thinkin about doing dual cooling. should i set it up like my sj; one line from pump to "T" then from "T" into two spots on the exhaust...

are the OEM fuel filters on a SJ any good? i have gone through quiet a few other types of filters and it seems they don't last to long... right now i have large paper type filters on my SJ and they only have about 6 rides on them and i belive they are getting pretty cloged. i can ride for...

is this correct? 62T flywheel has two round holes in the face of it and 61X flywheel has two "D" shaped holes in the face of it? i searched for pics, and searched i know there was a thread a while ago that had a pic of a side by side of both flywheels but i cannot seem to find it!

i just got a new set of pistons and a fresh bore and hone, when i put it all back together should i just put it together dry or should i wipe down the bore with something to lubricate? all the old timers i know that have been building motors for longer than i have been alive say to wipe...

i am replacing the top end on my 62T/61X because it was worn out, i read alot about air leaks caused by old crank seals... what needs to be taken off to replace the crank seals? i would guess, the flywheel, and the coupler? i already have my motor out and top end off so... i shouldn't...

will a 2008 sj hood fit the 96-07 sj? are there any differences? and are the poles the same?

when you guys run foot straps, how much of your foot goes in them? i was thinking to be safe, maybe just have my toes poking out of the strap and no more? that way when i come off it i don't mess up my ankle, too bad... they are going on a B1, if it matters... thanks

thong bandit hooked me up! i got 6 black dakines for a great price from his recent thread in the for sale section. he came across a load of foot straps and passed the savings on to a few people here on X. just wanted to say thanks again buddy! :You_Rock_Emoticon:

how does powder coating hold up on a b pipe chamber? anyone ever try it? thanks

i am installing tubbies on my RN SJ i used 5200 and screwed them down, now i am sanding and prepping to glass over them, my question is, is it ok to sand down the little bit of 5200 left on the outside of the tubbie and just glass over it? its not a whole lot of 5200. should i do something...

i am in the process of defoaming, re-enforcing, etc etc... i am in debate of painting the eng compartment or just leaving it after glassing... those of you who have painted it, what paint did you use? rattle can? i think my biggest worrie is will it start to peel from a bit of water...

i just got a B1. its got a blackjack carb, FP limited pipe, and protec rec head. i looked at the cases and cyl. case has 6M6 casting marks and the cyl has no casting marks that i can see, on my other two skis with 61x cyl's the 61x mark is casted between the cyl's on the carb side. so i...

i noticed one side looks like chopped glass and the other is more uniformed, the fibres all go one direction. is there a top or bottom side when using this glass? its 12oz, and im putting the panels back on my tray that i cut out to de foam. thanks!

i have a Riva scoop grate on my RN right now. it was on there when i bought it. i see the worx is a very popular intake grate. how does this riva compare to the worx? i ride mostly flatwater, trying to do tricks... oh and i have a D cut stock rideplate too. thanks

i am re-foaming my tray on the superjet, installing a scupper and fixing leaks. i am pulling all the foam out. my question is, when i pour the new foam in should i pour in a little and let it expand then pour some more, and keep repeating untill its full? or should i pour in alot (how...

seems like everyone here likes the blaster mod pipe, but they are getting harder to come by and expensive... so whats the next choice for a good pipe for the blaster? i just got off the phone with FP, good ol cindy says she doubts they will even make the mod pipe this season, but it seems...

Any head gasket differences for 64U or 61x head? my 99 sj is 62t/61x with 64U head my 94 B1 is 61x/61x with 61x head at the dealer they show different part numbers for the head gaskets, can they be swapped?