Search results

WDK rok-r fiberglass layup. Bare hull no title. All superjet running gear work on these hulls. Paint in ok shape some scratches on the bottom. Turf in good shape. Located in Vancouver Washington $1800 obo

I have a limitedslip 3.3 gallon tank for sale in great shape. $300 shipped obo

Anyone know what type of gas tank this is. Bought it a few years ago and not sure the manufacturer.

Ive got a used thrust ez-flow pro 144 trim system. Parting out a barely used ski and don't have a need for this. How about $400 shipped?

How many people have had to change out charge coils on stators? I have had to change out the charge coil on two of my skis In the last couple of years, skis would run awesome when fired up but slowly deteriorate as they got warm. Both are mid 90s a squarenose and a blaster but the electronics...

for those of you who have had a ROK-R hull, how long was your pole? I know they are usually VERY short but i'm a shorter guy (5'7) and had to bend over the whole time to ride. Got any rough guide to start by? Running a KP pole with tubes so adjustments aren't impossible just a PITA to stretch...

I'm having a weird carb tuning issue, I've got a WB1 with a few mods, ada head 180psi, riva red pipe, lightened flywheel. Starting to try and tune the ski with dual 38s that were recently rebuild and are clean. 75 lows and 135 highs with 2.0 needle seat and 115 gram spring making 30psi, carbs...

can anyone who had been around a while explain what is going on in this thread post about bendix removal, the pictures are no longer working... http://www.x-h2o.com/index.php?threads/improvised-tools-aka-knuckleheads-at-work.33400/ I've got a bushing that needs replaced and have the 1/2" tap...

Hi I've got a few props laying around from parted out skis and cant seem to find a lot of info on them does anyone have any ideas what they are? #1 is an unmarked yamaha 144 prop with E59 stamped into it. #2 is a 144 yamaha Skat-Trak that has 6 3 v stamped into it. #3 is a solas YB-SC-C Thanks!

Is it ok to block off the rear hood vent on a blaster and just run the front? I have a mild 701 motor in it and am currently painting the ski so I'd like to do all the body mods that are needed now. Thanks Mike

My buddy has a sn 650 that has a protec pipe and ported head... He was running a single 44 carb but we had a set of dual 38s laying around so he put them on with a protec manifold and aftermarket arrestors. Protec recommended 107.5 mains, 65 lows and 2.0 needles with 80 gram springs... With...

just put together my new motor (61x head on 62T cases). I sealed it all up and let it sit for 24 hours before doing a leakdown pressure test. I've found that my brand new front crank seal (oem) is leaking pressure. It will drop about 1-2psi a minute when i pressurize to 8psi or so. Is this...

Can anyone tell me what pipe this is? Are they any good? Thanks

can anyone give me a link to the correct fitting that will connect a factory type 4 dry pipe to a metal superjet waterbox? I have jimmy rigged one out of an old exhaust pipe but it looks like it needs to be a bend with two different diameter pipe sizes. Thanks!

I recently put together a new 735 jetmaniac ported motor and picked up a blackjack 44mm carb to put on it. On the first ride out the plugs have been fouling horribly, so I bought a pop off tester and my pop off is reading about 12psi! What needle valve would you suggest for a 735 with a factory...

Can anyone tell me if I'm doing anything wrong with my steering cable. Bought a new SBT cable last season for a ski I was building (stripped hull) so I was putting it back together. The steering cable stripped off the crimp just like in the picture within the first couple of rides. It was the...

Should there be any noise from any of the bearings on the crank when spun? Particularly the bearing next to the drive coupler? I have my motor apart for paint and new top end and I thought I would check out the crank while I'm at it. The bearing next to the drive coupler is tight but makes a...

I bought a SN superjet that had some spark issues, turned out to be the stator... but when I opened up the ebox it has a protec adjustable CDI. Are these similar to the MSD enhancer? Any benefit in switching to the MSD enhancer on a mild freestyle performance ski? Thanks!

Does anyone know off the top of their head what size the exhaust bolts on the 701 motors are? I bought a empty SN hull and a 701 motor didn't have any exhaust bolts installed. Thanks! Mike

Sorry another water routing question! I've searched and searched and can't get my head around how the water gets routed in my (new to me) 95 SN. I bought a completely stripped hull and seperately bought a stock 61x 701 and factory pipe (he said its a dry pipe). this is the exact pipe I have...