Search results

So I have a dasa 1000 I bought from a member. It has 4 outlets on the head and also two more on the sides. I have been searching pictures of others and I see some with just two on the head, others with 4 but none with the two on the side. What is recommended? I understand that the top ones go...

Putting my ski together, running a zeel with 760 electronics. Thought my starter relay was bad but same problem. It’s not the start stop, checked it with meter. I’m not getting power to the other side of the relay/solinoid. I’m wondering if something isn’t hooked up correctly. Not sure where to...

Just picked up a kdx with a 148 mag pump. For now I'm just going to put my jetmaniac 735 w/b-pipe in there. What impeller should I use. I read somewhere someone used a 6/12??

Like title says can be titan or badass. I'm a flat water guy so I will be going full carbon when I buy. Thanks

Looking for direction and advice on which pipe to choose. Pfp seems to be the top choice. I'm just a flatwater rider that is just wanting some more power. Planning on going with a hpe 5mm. All have pros and cons but I'm looking for something that is fairly easy to tune and is going to last. I...

Does a superfreak badass require a shorter drive shaft? Will a limited b pipe chamber fit? Do you need a special intake grate? Anything else special? Thanks

not sure if it has been posted but looks cool. https://360fly.com

Was riding the other day and at the river I ride at there is some moss and sticks in the water. Never have a problem with them but the other day was heading back in and went over a little patch and it felt like my ski suck up some moss because it started to burn out like cavitation. So I stopped...

Grandma just bought a house on the river and right now it has just the wood dock but I think we are adding the plastic dock as well. Question is anyone have a good way to "dock" the ski. I'm thinking an aluminum ramp that can slide and drop with a winch.

Put a scat mag in my ski and had a shimming question. Stock pump only required one thin shim on each of the back bolts. With the mag in one side doesn't require any and the other requires 3-4 shims. Is that normal or did something get twisted? And do the shims have to fill the space tight or...

Bought a mag pump and I put my driveshaft in it. Bearing felt nice and smooth before they went in. Now when I hold the driveshaft and spin the housing I can feel some small bumps but not all the time. I put it together once already and didn't like how it felt so pulled it apart and the rear...

I know there are lots out there but what's everyone preference?

So I was going to go riding today and started my ski before loading it in the truck and it took off. Been doing some reading and sound like I have a leak somewhere. The only thing I have changed was the domes and that was like 2 months ago and it has been running great. Is there anything I can...

I can't even think straight because I'm so frustrated with trying to put back the pole bolt through my new blowsion spring. I have a rrp cast pole with blowsion dual breather bracket. Is there some sort of trick to get it on or I'm I just stupid? I have the bolt started through the spring but...

So I just change the domes in my blowsion head from 37's to 33's. I'm at 3,300 feet and compression before the change was 150 and it only changed to 165. I was expecting 180. Is something wrong or is that what it should have done?

So I have a piece of junk 550 the has been a pain in the butt to get tuned. I have a sbn 44 with 120 high, 100 low, needle and seat 2.3 with dull silver spring which the manual says should put the pop off at 20psi but I just check and I'm getting 10.... So should I get a new needle seat and...

I have a 10/18 skat impeller and I can't seem to find out anything about it or what it is comparable to. I want low end and I read everywhere to get the hooker 9/15 but I would like to know where I stand with what I have. thanks

So I picked up a super jet yesterday and today I noticed it leaked a bunch of fuel out. It was leaking out of the "ON" side of the pick up line. I did some looking around and all the ski I see have lines running from both the "res" and "on" but my "on" have a screw in it. I'm sure that was...

I'm fairly new to 2 stroke motors and tuning them. I will be picking up a superjet here in the next week and the elevation where it is now is pretty close to sea level and I live at 3500ft. I'm I going to have to re-jet it or just tune the carbs?

Looking for some feed back on helmets. The fly default and giro freeride seem to be the ones I'm leaning towards. The fly is 50 bucks cheaper but looks bulkier. Any input appreciated thanks