Search results

Came back from Tona after ski ran perfect. Li fe Battery was dead. Bilge was disconnected for trip. Should have disconnected ground from batt. Oh well. Anyway. Put standard battery charger on life batt on 20 amps for 5 sec to bring it back to 12 volts then switched to icharger and fully charged...

Jetmaniac lay down pipe waterbox has a substantial smaller inlet size and longer than the rrp stock box. Will this act as somewhat longer narrower stinger. Anyone have experience with this wb and rrp. Higher rpm? Add more fuel ?

I checked pop off and pulled jets everything seems normal but front carb keeps going lean even with adjuster screws further out than rear Cylinder. Pulled fuel pump and seems like there is a good bit of range motion on the clear diaphragm compared to another spare I had around. The whole pump...

Another log in water geez. Hit me up with what ya got

Anyone tried adjusting the stinger size down on a carbon pipe. Ideas?

I’m use to seeing some moderate temp differences in 62 t base motors I’ve had in past but current 964 is running much hotter on front cylinder in and out of water. Plugs read sim on both. Anyone experience this ?

Been through a few antigravity batteries 16 and 20 cell fit. Box is approx 6 long by 4.5 wide. Hadn't found anything over 20 amp hrs 5000mah. These won't quite make 2 tanks with tl and minimal restarts.

who sells these now? cant find him here.I get random click from mine, anyone else have this happen on older ones?

I was riding flat water with screws out but surf too much water accumulates when riding. These are perfect. Rc boat drains clog to easy. Perfect size to fit in sf and others very low TI hooked these up just right

Ive bought a few props from skat direct and impros,custom stuff,or bent my own and sent in for balance and refinish. They are always off by 2 deg or more on the leading edge and dead on with trailing according to watcon gauge or printed adjustable gauge. They say they measure theirs differently...

trying the longer style bpr plug with bit longer electrode. what plug gap is best with msd tl

Looks like rrp and jetworks have new systems out,anyone have any opinions on these.most angle least blow by on turns. Ive got the thrust and xmetal and kinda like the extra throw of the xmetal,but even dialing out steering I still have the bpipe coupler blow through once in a while,been...

how many are using the skat reduction nozzle with swapable rings,no veins,make much diff? using the 65v,doesnt take a very large bore.paper thin. what type and size are most running with the larger 900 to 1000 motors. Seems like prop setups are getting closer and closer to stator with some...

There have been some really impressive results coming from 900 cc motors recently,what would most prefer?a 900 with 10 mill or smaller crank? Many diff opinions on this, case strength,square cc to stroke,piston weight,rev speed,flow room for transfers.life of bearings,maintenance intervals,among...

First prop looks dead on 15/19 to me Second 148 prop. Let's hear opinions. Pics taken at 12 low leading edge and higher 15 leading edge in the gauge. Lastly 18 trailing edge

Anyone have pics of their 148 pump in the welded 144 housing, Ive seen quite a few skat pumps crack the housing in salt water use,anyone have long term experience with one of these in surf? I had a 148 in a 155 housing that swelled bad enough to bend up the stainless between the veins where it...

I have swaped in a few mag pumps last week and have since grinded the crap outa this pump shoe for better centered fitment,These were the pics from taking the original solas mag out,this these hulls apparently have a pretty decent angle on the pump to be aligned in the hull. Why would the shoe...

One of these is a few yrs old and one is newer,how many have the flat leading edges like this? I dont really get why they are labeled like this either,one is labeled 10/16 the other is a 11/17, On a prop gauge one is 13/17 the other is 13/16 on one blade,16.5 on another and 17 on the third. I...

Tired of mailing and waiting on impros out west,ive found island racing and speed freeks in ny,anyone have any experience with these or know any others not to far from the mid atlantic

I have some prop gauges and a rig to bend props on a draw tite to get some leverage,vise isnt cutting it. How important is it to bend close to the root angle? kinda hard to get that far back in there with a good size tool. Was talking to Dave about the skat mags and there isnt alot of different...