Search results

I have a 701 Raider thats been running great, however today it started hesitating from 1/2 to full throttle and would not get up to speed. If I sat and let it idle, it would run fine for about 50 yards then start to hesitate/bog again from 1/2 throttle up. Ran fine from idle to 1/2 throttle...

on a 97 Raider. Small white box sitting where a bilge would normally go. Thanks

Just bought ski and thinking these are still good, just the outside covering cracked but wanted to check with the experts? Good or not? Thanks

this ride plate. Just bought ski and not sure what its sat in, what is this and what will take it off? I used a wire brush on a drill to get the flat areas but before I scrape all the little squares I wonder what I could spray on or dip it in? Thought about CLR but it says not to use on aluminum.

New trailer and unsure how to secure SJ at the bow. On old trailer I used the Stoltz bow stop but this looks to have a short vertical post and I am not sure one of those would work. Thought about getting a winch strap with the smaller strap at the end, loop it thru the hole on the SJ and...

this stain in the bottom of a Waveraider that I just bought. I thought it was an oily residue due to the raider having the auto oil injection however I have tried, acetone, grease lightening, microbe, dawn, gasoline, super clean degreaser to get it off and I've really do not see much progress...

Just bought this Waveraider, which has the auto oil injection. Its been sitting for several years and had half inch of water and oil mix in the bottom. Cleaned it out and now left with this stain. Any ideas how to get it cleaned up? I've tried Dawn, Grease Lightning and even some acetone but...

looking to buy this ski, do you see any issues with the engine compartment?

Got a 2014 Superjet, just rode in salt water. Went to use the backflush kit I made for a blaster but it will not go into the pisser, anyone know what size I need to use? Thanks,

Put a pipe on a blaster but still have stock head, what can I use to plug the small water outlet on the front cylinder? Thought I had it plugged but it came off yesterday, causing water in the hull. Ski would also run fine then just shut down while riding. Would start back after a few minutes...

Is there a fix for this other than drilling out and tapping? The screw was stuck, would not go all the way in or come out with screwdriver. Used some vice grips and of course it turned the head off. I was wondering if this was a ground and I could attach to the top screw or ground on another...

I recently replaced the head. In the process I was going to go with the ADA head/girdle set up. However once I got it on I was not getting the compression I should have and found out my blaster has a 650 in it. I went back with the stock head and had the carb rebuilt. I got everything back...

I have been in the process of installing a new JM head on my 94 Blaster. Got it done but did not have the compression numbers I should be getting with the new head. JM has been great in helping me figure out what I did wrong with the install and in the process, I discovered the Blaster I...

Going to put on a jetmaniac head this weekend. I looked at the directions and they seem pretty straight forward however I do have a couple of questions. After I take the old head off, I will be putting the domes on first, then the head itself, is that correct? What kind of grease do you use...

94 Blaster had been running good last season. The first time I tried to start it this year it gave me a little troble but started wtih a spray of starting fluid at the house. Got to the lake and again it struggled even with spray. I played around with it, went from ON to RES a few times and...

double post, sorry.

Had some issues this weekend with starting the B1 and believe the problem is in the selector valve. Got it running thanks to Quinc's help with running the res line directly to the carb but now think its just best to replace all the lines (believe they are original ones) and valve. Any...

05 that has started just fine until I rode it about 3 miles down the inland waterway. Stopped to give my finger a break and when I tried to start it, nothing....not even a sound. Where do I start? I've replaced the on/off switch last year and its in good shape still I would think.... Thanks,

94 that ran good for about 30 minutes, changed spark plugs then it starts, runs for about 20 seconds and cuts off. I dont think it has anything to do with the spark plugs because the first time we ran it this year it did the same thing and I turned the selector back a little and it ran fine for...

Added head and protec pipe to blaster and re-jetting carb with protec kit. Per instructions, turned high speed out 2 turns and low out 1.5 turns. Can anyone tell me the additional adjustments they had to do with a new pipe and high compression head (165) when they put it on the water? Is this...