Search results

Tiger Craft v2 aqua bot with a 10 mil 1000cc Dasa. Novi 48s, TNT Lay down pipe and water box, blowsion light weight handle pole, Rrp ovoid steering Rrp riser bars Rrp Carbon chin pad Msd enhancer Rrp lightened flywheel(3* advanced) Yamasaki coil Billet couplers Limited slip tank 148 mag -4...

Tiger Craft view to aqua bot with a 10 mil 1000cc Dasa. Novi 48s, TNT Lay down pipe and water box, blowsion light weight handle pole, Rrp ovoid steering Rrp riser bars Rrp Carbon chin pad Msd enhancer Rrp lightened flywheel(3* advanced) Yamasaki coil Billet couplers Limited slip tank 148...

just ordered a crank and some other stuff from jet maniac and just like always, best service in the industry and the parts are top notch,thanks to the maniac for making this stuff super easy,don't check prices any where else, just hit up jet maniac and thats as good as it gets…..

i have a 24/7 scupper installed on my ski and the rubber flapper is bad and i can not find a replacement for it,can i take the whole scupper cover off and replace it with an rrp scupper or what , any suggestions would be helpful,i am thinking i will just glue it shut and wire my bilge to run...

will a nozzle from a 99 gp 800 fit on my 96 superjet? also where dose everyone buy there bilge switches from,my blowsion one went out. thanks for the help.

real good dude with great products and ships fast,highly recommended,thanks again mike.

optima racing is awesome. great customer service with great communication and very easy to deal with.A++++++++++++++.

optima racing has awesome customer service and great prices,i have ordered from them many times and its always one step better than any other company i usually deal with.it not that other parts people are bad or lacking in customer service, optima is just better , thanks for being rad mike b and...

im on a 750 sx,medium-heavy porting,rd o-ring head 195lb in each hole,duel cdk40's,factory pipe limited with flow control valve,rd timing advance plate,and i would like a prop that is good for rec riding and will give me the bottom end punch i need for free style,but if i had to go one way or...

i was wonering what the advantage of using the pump spacer wedge is,do i need it or can i run without it.

http://sacramento.craigslist.org/boa/2639179408.html get some.

i just bought a new motor and i am not sure what octane to run for the break-in,also what 2-cycle oil isthe best to use,here is the post on the motor i bought.please help if you can. http://www.pwctoday.com/f149/built-750-motor-fresh-ready-race-342534.html

new motor and factory limited pipe and i dont know where these hoses coming from the ebox go,please help if you can.

i am installing a pump primer on my 750 and i put pump primer nipples on both carbs,is this necessary or do you only need to prime one carb,i put nipples on both carbs because i was afraid of waring out the cylinders unevenly on primed cold starts,was this the correct way or is it overkill,thanks.

i am putting a x2 trim set up on my 750 sx and i need a tube through my hull to run my cable so i dont have to use my stock syphon bilge,my question is,if i drill a hole strait through the hull directly above the 2 factory tubes(bilge and water intake nipples) will i run into any of the stock...

i just put a big pin motor in 750 sx and i went from single carb to dual carb and the linkage on the new twin carb is going the wrong way,so i can not use the stock throttle cable mounting bracket,is it possible to change the linkage pin with one that has the right linkage direction and if so...

just want to know what other trim systems will bolt up to my 750sx other than the x2 setup,and if i put a trim on will it effect my every day riding,thanks to all.

i striped my ski all the way down to the fiber glass(the entire hull),and on the bottom of the hull i dont know if i should jel-coat it or paint with multiple layers of clear,also i wasent sure if i would have to get a new tip for my paint gun to spray the gel coat,all help would be greatly...

i found a 92 750 sx for sale and i am sic of trying to do flat water tricks on my old 650 sx,is the 750 sx powerful enough for barrel rolls and possibly flips , and will i hit the exhaust when installing footholds,all info would be appreciated,i also found some sxi's and dont know the difference...

i need help with my cooling intake,souuld i drill and tap my head or is this routing wrong,this is my first ski and i am lost,please help if you can,i drew a pic to try and help.thank you.