Search results

Hey guys, I've been trying to get the driveline on my ROK aligned properly after my recent driveshaft / midshaft failure. I've aligned the pump / midshaft to perfection using a CF midshaft tool, so I know they're in good shape. My next task has been to align my engine to the midshaft (CF...

Hey guys, I'm going to be running oem 44's on my ski, and I'll be blocking the cross over passage. I'm wondering if I need to use the OEM Spacer with this setup, or if I can just get rid of it? Thanks -Rob

So I picked up a GP760 a few months ago that had bad piston scoring after being run completely out of oil. The engine came apart ok, and I didn't see any corrosion in the cylinders or crankcases / crank. The crank it's self has very low hours, and was replaced just before it was run out of oil...

Hey guys, Heading down to San Antonio for work this September. I'll be in town from September until March. Any reason to bring my ski with, it's a big hassle to get it there, but if there's some decent riding around town, I can bring it. Thanks -Rob

Anyone used a bilge bracket in a ROK hull? It seems that the floor of the bilge is too close to the midshaft housing to use the bracket I have here. Is there another one that would fit, or should I just mod this one? -Rob

Hey guys, I was riding my 61x SN all weekend, and on Sunday after riding for a while, it wouldn't restart, the battery was nearly dead. I pulled open the ebox, and found the following: Resistances: Green 1 to green 2: 1.1ohm Green 1 to ground: 550k Green 2 to ground: 550k Voltages, engine...

Hey guys Finally got my new ski out on the water today, and left not so happy. The current setup is: 94 SN 61x/61x B-Pipe Jet maniac porting Ada head (175/175 psi) Blackjack 44 Hooker 9/15 The ski ran like a dream for about 45 mins. Plenty of power, nice throttle response, pipe not too hot...

Anyone have a picture of this they could post? I picked up a used pole and I'm not sure I got the right parts. Thanks -Rob

So I recently purchased a 61X/61X SN from a member down in GA. I got it home and just now started to mess with it. It has perfect 175/175 Compression with ADA 35cc domes, and a Jetmanic port job. I noticed that when I fired it up, there was a little smoke / fluid leaking from under the coupler...

Hey guys, I picked up a new single trailer yesterday and I'm going to be setting it up for a pair of standups. The issue is, I don't know what hulls I'm going to end up with! I currently have an X2 and I'll be picking up an SN next month, with the plan of swapping it into an aftermarket hull...

Hey guys, I'm looking at picking up a ski from someone down in Daytona. Is there anyone heading north with an open trailer spot? Let me know! Thanks -Rob

Hey guys, I'm making the jump into a Yami, and plan to end up with an aftermarket hull sometime in the near future. My plan was to pickup a 701 RN with some basic mods, and swap everything into a ROK or other similar hull. I've been thinking about it though, and I can pickup a 701 SN for...

So I've pulled apart my stock intake setup, and noticed that there's a spacer between the carbs and the intake. Do I need a total of 4 carb gaskets to get this thing bolted back together? Thanks -Rob

I had a nice pair of sunglasses wash up on the beach next to me Sunday, anyone lose a good pair? ID them and I'll get them shipped out to ya! -Rob

-Rob

So a buddy and I were bored hanging out in the garage the other night, and decided to shape some metal. It's still a work in progress, but it's looking good so far! The plan is to fit it in the front fuel fill port, and then have a normal fuel cap where the pickups would have been. -Rob

Hey guys, I'm thinking about flying down from Michigan without a ski for the freeride. I've never ridden in beach surf, but I love 3' Lake Erie chop. Is there much opportunity to rip around on a borrowed ski? Thanks -Rob

So I just realized I stole the fuel tank strap someone loaned me to hold my battery in. I forgot to return it at the dock, and just now tore into the ski. Whos is this, and how can I get it back to you? Thanks! -Rob