Search results

Hoping I can get some opinions on what to look for to remedy a bogging issue on a 2013 bone stock Superjet, no mods what so ever. Symptoms: Hard start when cold: choke helps sometimes, other times need to pour a bottle cap of fuel into carbs to start Once started idle is more or less OK until...

Will an SBT cable with part number 26-3403 fit a 2004 RN Superjet. I think that part number might be for a squarenose but i need to confirm. Thanx Sent from my iPhone using Tapatalk

Bought a replacement starter a while back and finally got around to replacing the old one. Problem is the new one doesnt match. Check the pic and let me know what u think. Sent from my iPhone using Tapatalk

I'd like to buy a tap to try and clean the threads on a set of 38mm mikuni's. Can anyone confirm which tap ill need for the pilot and main jets. Thanks Sent from my iPhone using Tapatalk

I have a G/flex repair kit that i plan to use to replace the pump shoe on my superjet. Its been in my garage for almost 2 years. The hardener has some dark red deposit at the bottom of the tube. Has it gone bad? The clear resin tube looks fine though. Below are some pics, let me know if i can...

Looking for help in deciding what to purchase next for my RN. Currently have most of the standard bolt ons for my 701, B-Pipe, head, reeds etc. Hull has holds and good turf. I am looking into aftermarket hull options but am not yet ready to pull the trigger. Any further mods i make to my...

hey guys, i'm trying to get an idea of how difficult it is to replace the front and rear crankshaft bearings. The front crankshaft seal failed on a buddy's 701. while replacing it we noticed the black plastic race on the front bearing was cracked and we're not gonna reassemble as it is. (not...

Ive been following an issue over the past couple of months. I find that while riding water builds up in my fuel filter (oem filter). So there must be water in my tank. I notice the effect on my engines performance, i take it to shore right away and inspect the filter. I drain the filter...

Quick question: can the crankcase on a 61x/62t be split without removing the pistons from the rods? Sent from my iPhone using Tapatalk

Quick question, will the ride plate from a 2013 superjet bolt directly onto a pre '08 hull? Any advantages/disadvantages to doing this. I busted my stock plate and can get an '13 plate quickly/easily. Sent from my iPhone using Tapatalk

I have a kit thats got the fuse holder wired in. I'm trying to figure out how to put it into the ebox and still be able to access it without having to reopen the whole thing. The screwed-on cap that gives acces to the main cdi fuse seems too small for both fuse holders to fit. Any suggestions...

Short version Piston pin bearings rusted and crapped out with lack of use. Removed cylinders and pistons cant move. Best case scenario i'd need to replace pin, bearings and clips. Pins however are stuck, I can't get them to budge in either direction. Any recommendations on how best to remove...

pulled the flywheel cover and flywheel today...man its ugly in there. looks like there was grease and some oil flying around. besides the bendix, didn't think anything in there gets greased. is this normal?? i'll snap some pics and post them up later. just making sure before i start chasing a...

ok i need some help picking out a graphics kit. i've got it down to three very similar ones. curious what everyone thinks. worked it up first on exotic signs and then photoshopped a little if u don't like em at all, i'm open to suggestions but definitely want to stick to the red and black theme!

i keep having the same problem with my lanyard getting caught and breaking the cord. i use a clip style lanyard always attached to my vest. when i do hood tricks (especially riding backwards) the cord gets caught under the chinpad. if/when i fall or try to dismount the cord stays stuck, breaks...

i've seen this on www.thehulltruth.com a boating forum i'm on. its a link that pulls up all recent posts which have not had any replies. if there's already one here...oops please let me know where it is?

While riding yesterday I felt a new vibration. From a dead stop if I punched the throttle I felt a slight loss in power.if I revved up slow it was much better but full throttle still felt weak with a high free vibration. After pulling the ski out I checked the pump for any junk. Nothing in the...

Friends SXR 800 b-pipe, flame arrestors, rejetted carbs, otherwise stock. in front cylinder, piston keeps closing the spark plug gap. Sometimes it closes it enough to loose spark completley. what could cause this? if piston is over reaching, i suspect a failed/failing rod bearing. could that...

Just wondering where u guys mount the thru hull fitting for a bilge pump on a RN. and advantages left side vs right side. thanx btw its a rule semi automatic 500gph

been reading on here for a little while and just started posting so i'll introduce myself. first off i bought Bill Adkins 2k4 squeeky clean RN :Banane01:. the one advertised in Yamaslut's signature. i live and ride in HAITI. all flatwater, so surf nearby... ski was shipped out of miami...