Search results

All SOLD....

SOLD SOLD SOLD SOLD SOLD Hull: 2014 Trendsetter’s Backie Chan Fiberglass Custom paint, top and bottom Turf is brand new 2 custom ALUMINUM ride plates (Flat water and Surf) X Scream Comp pole Thrust OPV steering Fri skeleton throttle and trim levers Fri surf switch Fri pole limiter rope Thrust...

Looking for a 9/15 prop for a 148mm pump. What is out there guys?

Looking for an aftermarket intake manifold and a set of dual carbs for a 701. Carbs can be 44 or 46mm.

Found

SOLD, PLEASE REMOVE... ET967 was rebuilt last year with 94.5 pistons with new PV set up when built. Cylinders are still fresh looking hone as the ski was fogged after every ride, and ran on the fat side. OEM crank and case work was done by Art at ET. Comes with 2 sets of pump gas domes, extra...

Looking for a FP Head Pipe, with all 3 screws not frozen. Let me know what you guys might have stashed away. PP ready.

Looking for a set of domes for an ET967. Perferably race gas or higher compression than mine.

Looking for a 148 set back mag pump. Prefer it to have a good shaft and prop if possible. Going to run with an ET967 motor, Thanks in advance....

Selling for a friend who cant seem to get on here because of his login. Dual 48mm Full Spec carbs Dasa billet intake V2 reeds Carbs are set for external fuel pump. 1000 obo.

Hey guys, Been looking for 2 days now on here, and trying to figure out the temperature ranges on the cylinder, head, and pipe. The motor is a BigBore running 86mm, Factory B pipe, and ADA head. Motor is reading with my temp gun, 130 on the cylinder, and 119 on the pipe. I know the pipe...

Found. Please DELETE...

I have a 144 Solas Mag pump in a 14 Trendsetter Chan. Looking to see if going to a 148 setback mag pump would be a noticeable difference, bang for buck kind of thing. Trying to find some gains without going to a bigger motor. Right now I am running a 781bb motor.

What intermediate housing is used in the BOB hulls? A friend of mine bought 1 against the advise he was given, now his problems start, LOL... Any idea, looks like an old 550 housing to me. I am not a Kawi person, so I have no idea, and he is too LAZY to get online and ask for himself.

Anybody have a Backie Chan ride plate they would want to sell? Been trying to get with Gary for 2 weeks now, with no answer.

Looking for a limited or mod chamber for a superjet. What's out there guys.

This is a 62t / 61x 781 big bore JM motor, with dual 38s, MSD Enhancer, MSD coil, and lightened flywheel, running 188 psi. Ok, long story short. Rode Daytona free ride, and at the end of the ride, noticed a little break up at top end. Got back to shop and flushed out . This Saturday, went...

Been having a nightmare trying to find 12oz dual biaxial cloth without the 3/4oz mat. Can somebody please put me in the right direction for this, as well as a good epoxy resign? Thank you in advance guys.

Hey guys. I have a 3rd gen rockered nose kit that has the splash guard / bond rail built in. My question is, can I cut off the splash guard / bond rail? I think I remembering Carter saying I could, but not 100% sure. Pics attached of what I am talking about. The black marker on the nose is...

Hey guys. Kind of new to these dual 38mm Mikuni carbs. I have always ran duals that were independent from one another, so having a slave carb set up, is new to me, and has me a little confused. Couple Questions: 1. Should the fuel inlet barb on the slave carb, when looking through it, look...