Search results

I have a customer ski here and I am kinda stumped. He bought ski as it is and was having trouble getting ski started in the water. He brought it to me and I suggested going through the carb since history was unknown. Turns out it has an AM SBN 46 and the intake was opened up to 46mm as well...

Had a ski dropped off with this carb on it, ski runs but not well. Idles ok and part throttle it will accelerate, although not great, at any point if you grab full throttle it just falls on its face and dies. On the trailer sounds crisp and revs but in the water acts as described above. my...

Interesting http://motherboard.vice.com/read/the-faa-says-you-cant-post-drone-videos-on-youtube

http://boston.cbslocal.com/2015/02/26/nearly-frozen-waves-captured-on-camera-by-nantucket-photographer/

I want to get a wrap for my pole with my reg numbers and want it to match the rest of my ski. Had one local shop quote me $475 for a 25 in x 18 in printed wrap installed, I promptly walked out. Had another local shop give me good price but asked me to email him pictures and measurements...

For those of you who were not at Daytona and have not seen the article in The Watercraft Journal, check this out http://watercraftjournal.com/inside-wildwood-sea-doos-spark-powered-krash-footrocket/ @chrisgrace

I am attempting to break down a pump that was in a blaster to swap shafts and install in a rickter. I have the spline tool and the impeller tool, got the impeller to break loose and made 4-5 easy turns on the shaft and then locked up. Destroyed the impeller hex tool shortly there after. I...

@Mikesee Have not seen him post up since before Havasu

I have a power factor on a 701 I have been running for a while now, runs good, makes good power even though I am still a little rich. pulled engine and pipe today for other reasons and noticed that all the turf I had glued to the bottom of the waterbox was shrunk up, melted and almost all gone...

I have a WDK Envy and up until last week I was running a kawi 750 with a shaved head and factory pipe. It has a Kawi 140 pump with an 11/19 skat impeller (i beleive) gotta get in there and double check, and a wetwolf cone. After having electrical issues again I got fed up and swapped in a...

So I bought a pfp a little while ago because it was a deal, figured i would use it eventually. I was out in the garage just kinda going through parts and seeing what I had laying around when I realized that the pfp manifold I have has 8mm bolt holes and 62T cyls have 10mm holes. I read a bunch...

Made it out for a bit today. Water 38f, air 20f, wind 25-30mph, but the waves were fun

I purchased a dry suit from McDog and it arrived quick, was well packaged, and is in perfect condition. Would buy from again Jon

I contacted Wrighteous and agreed to buy a PFP he had for sale and he agreed to bring to Daytona. I got to Daytona and find out he didnt make it because he was in the hospital, no big deal, can't get mad at that. I had given a deposit and was not in a hurry for it. Charlie kept up on...

Got my parts as promised. Thank You Jon

So for the last week or so, yes before the big update, I have been getting notifications on my phone from tapatalk that I have messages or people have replied to threads, but when I go into tapatalk I have no notifications or messages. Today it started sending me messages about replies to a...

So I bought a WDK Envy, its setup to ram Kawi parts. Took everything out of my 750SX and am getting ready to bolt in the pump. Are you guys using the stock rubber seal that wraps around the pump or just using silicone? What are you attaching the pump shoe with? This is my first time assembly a...

I just purchased a new envy From Pat (moto360) and the plan was to swap everything from my 750 into it. Well got it home last night after 12 hours in the truck and ripped into it this morn. Pat gave me 2 drive shafts, plus the one from my 750 and none seem to work, needs to be about 2 inches...

I have been lurking and reading this forum for a little over a year now, although I have made a few posts, mostly I have been buying parts. I figured it was time to formally introduce myself. My Name Is Jon, I have been riding for about 2 years now. I am in South Jersey, right outside...