Recent content by ultraclearance

Thanks! So even after i have grinded the sponsons-bolts down and have clearance all around the pipe i should still dent the pipe? Its alot of vibrations i guess so need good clearance.. How "deep" should the dents be where there are sponson bolts? 1cm? i dont want to ruin the chamber.. was...

I will get it welded. But relocating sponsons sound like abit of work.. the ski is newly painted. What about grinding the sponsonbolts 80% down(leave a about 30% of the locknut), sand them round, and then put turf along the side of the hull where the pipe hits and over the bolts? Cant imagine...

Hi About one year ago i installed a bpipe in my 2003 superjet. Worked great, but now after 15-20 hours of riding i noticed a exhaustleak coming from underneath the chamber Took the bpipe out of the hull and got a bad surprise. The chamber is rubbing on the sponson bolts, the top row. Made 1...

Update! I found the problem. I took it out again yesterday, and after a few minutes of riding it died again. But this time i wasnt able to start it, i Just heard this buzzing noise from the ebox, probably the starter relay. I wiggled the plus cable, and tighten it up, after that the problem...

Lot of good theorys here, thanks! I guess i Will start with plugging the hole in the chamber. maybe the engine didnt get enough air because of the leak, and thats why it died? Do you think jb weld will do the trick or should i get it welded at a shop? I did a compression test today, 158PSI...

I hope not..! I havent tested this season after b pipe, i did a couple of compression tests last year, it was 156 psi on cyl 1 and 158 psi on cyl 2.. Both times. Havent checked after bogdown, i will get back with result, hope my engine isnt damaged:/ I thought a small exhaust leak wasnt able...

Hi! Appreciate any help! i bought a superjet last year, pretty much stock. RN - 2003 Put it almost to pieces this winter, checked all parts for wear, and fitted a b pipe, primer, tachometer, bilge, ++ The only engine mod is b pipe and MSD - I used the recommended b pipe settings on carbs and...

Thats what i want to hear!! Yeah nothing is loose, i just licoriceed up by putting to much grease into it.. The housing is not new anyway so this winter i will replace it. i guess, the leak will get bigger before any big failure? The leak now is only a tiny little stream. I pull the hood and...

I agree with you.. but the thing is, the midshaft housing is actually not in that bad shape, i pulled it this winter and noticed the rubber lip on the inside of the housing where it seals to the hull had started to slip abit some places, but not much. the reason why its leaking is because i...

Hi, My superjet (RN) got a leaky midshaft housing, when the jet is sitting in water i can see a small stream of water coming from the rubber between housing and bearing. Not a big leak, i would guess it could sit at least 2 hours in water before it starts to get serious its no problem while...

Do you have any recommendations compared to stock? Before b pipe the idle was good, never died, and not to high. What is typically changing with b pipe? Do i need to turn idle up or down compared to stock? This forum is awesome! Would never made it without it Best Regards,

Ah! Im a moron.. I read the b pipe manual, and for some reason i misread the high speed setting.. see pic. I thought that meant 1/2 turn, but off course 1 1/2 turn. So i turn high speed to 1 1/2 turn out and hope for the best! Appreciate the reply:)

Hi! Sorry, i have been reading but cant find the answer im looking for. I got hooked on standup last summer, borrowed one from a friend, and three days later i bought my own:) Its a 2003 RN, stock I got a hold of a b pipe a few weeks ago and in the process of installing it. As far as i can...