Menu
Home
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Account Upgrades
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
kevbo's latest activity
kevbo
replied to the thread
GP 1100 with 1200 cylinders port matched
.
The bottom screw feeds the lowest fuel inlet hole. It’s to adjust idle mixture only. Pilot jet feeds the holes just above lowest one, it...
Sep 13, 2025
kevbo
replied to the thread
GP 1100 with 1200 cylinders port matched
.
An overly rich part throttle setting will usually help response. Couches spend a lot of time at full throttle so setting the top screws...
Sep 13, 2025
kevbo
replied to the thread
GP 1100 with 1200 cylinders port matched
.
The bottom screws are the low idle adjustment only. 1/4 throttle is the pilot jets. Lowering the pop off will do the same as using the...
Sep 13, 2025
kevbo
replied to the thread
Updated porting temp plate
.
Open/non-tuned exhausts are not the best application for any jetski since max torque is always around 5000rpm. Our pumps don't make...
Sep 11, 2025
kevbo
replied to the thread
Updated porting temp plate
.
One other thing to consider about port height is your exhaust system. Once you go higher than stock 61x timing you also need a working...
Sep 11, 2025
kevbo
replied to the thread
Blaster
96 WaveBlaster 1 (Redemption)
.
A tiny exhaust leak will make it bogg. Cracking the hood will troubleshoot that.
Sep 11, 2025
kevbo
replied to the thread
Updated porting temp plate
.
Low ports will limit power but they are the most responsive. I have found the throttle response gets slow unless you want to set...
Sep 11, 2025
kevbo
replied to the thread
Blaster
96 WaveBlaster 1 (Redemption)
.
Try cracking the hood and make sure the tank is venting.
Sep 11, 2025
kevbo
replied to the thread
Best pump for 2023 Yamaha Superjet
.
Use bearings with a C3 or C4 and make sure they aren't too tight in the housing. If they are overheating then they fit too tight.
Sep 9, 2025
kevbo
replied to the thread
How to add antifreeze to crankcase?
.
Dry rev it until the thermosensor starts shutting it down. That will push out all the water. Corrosion is the real problem so use cheap...
Sep 8, 2025
kevbo
replied to the thread
65v vs 62t 144 nozzle
.
An upswept nozzle will make a superjet porpoise. They may be beneficial on a flip ski although it could make boarding a short ski more...
Aug 30, 2025
kevbo
replied to the thread
PJS Viper9000 super cylinder w/total loss static timing
.
You need to be careful with timing advance until the main jets/top screws are set rich of peak power. After that it’s safe to use a...
Aug 30, 2025
kevbo
replied to the thread
SN oem factory build markings
.
I have a 93 that still has 03/92 hand written inside.
Aug 28, 2025
kevbo
replied to the thread
What Impeller for Stock Pump with 61x Engine and B-Pipe?
.
The FX1 was designed in 1991, when 550s with 440 pumps were winning the world finals. These pumps needed to turn over 8000rpm to work...
Aug 27, 2025
kevbo
reacted to
Big Kahuna's post
in the thread
What Impeller for Stock Pump with 61x Engine and B-Pipe?
with
Like
.
Kawi 140mm pump for the win!
Aug 26, 2025
Home
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top
Bottom