joeschuit's latest activity

  • joeschuit
    joeschuit replied to the thread B-pipe manifolds for sale.
    checked my b-pipe headpipe and a #53 drill fits through, so about 0.059"
  • joeschuit
    joeschuit replied to the thread Any contact with Rhaas?.
    Jetmanic sent Rhaas some texts on my behalf. Took a few days for them to reply back, but I'm now told they would be shipped out...
  • joeschuit
    joeschuit replied to the thread Used RN SJ Engine Parts.
    pm sent
  • joeschuit
    joeschuit replied to the thread H20 designs/fast elements?.
    I like the adjustability of them for my smaller etx9 battery, but after a couple months of hard riding the sides bent outward. It was...
  • joeschuit
    joeschuit replied to the thread H20 designs/fast elements?.
    I purchased a couple of his battery boxes back in june. About 4 days after my order confirmation I sent a facebook message and he...
  • joeschuit
    joeschuit replied to the thread Any contact with Rhaas?.
    I'm using a used set of oem couch mounts right now that I've been happy with. My plan was to get the warrantied set, sell them, and buy...
  • joeschuit
    joeschuit posted the thread Any contact with Rhaas? in General.
    I tore a set of Rhaas couch mounts a few months back and I've been trying to get them warrantied. Emailed them october 1st, then every...
  • joeschuit
    I had the same 1979 55hp johnson on my 10' invader. Great motor and power for the weight.
    • IMG_20200428_174717133.jpg
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    Making more progress. Crank is shipped out to Crankworks. Head is pinned. Not much room to do that, but there is two small areas for...
    • IMG_20211107_193432185_HDR.jpg
    • IMG_20211105_150405381_HDR.jpg
    • IMG_20211108_190723024.jpg
    • IMG_20211108_193748970.jpg
    • IMG_20211110_120605537_HDR.jpg
    • IMG_20211111_184012457_HDR.jpg
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    I did see the cylinder pictures and agree, something let loose. Overall the crank is decent but I can easily feel something in a couple...
    • IMG_20211103_162111176_HDR.jpg
    • IMG_20211031_151732889_HDR.jpg
    • IMG_20211031_125133805_HDR.jpg
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    Engine is stripped down. Turns out the base gasket was never trimmed around the transfer ports. I'm sure that didn't help airflow...
    • IMG_20211028_184653955.jpg
    • IMG_20211028_184700169_HDR.jpg
    • IMG_20211029_125727738_HDR.jpg
    • IMG_20211029_173046711_HDR.jpg
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    This rad crank has stock 125mm rods. I believe the hpe kit has 133mm rods. Ideally I would like a long rod setup for less stress on...
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    I got the degree wheel out and rechecked my current port timings. Exhaust opens at 89 degrees atdc(180 degree duration), transfers open...
    • IMG_20211027_183433709.jpg
    • IMG_20211027_182215665.jpg
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    I remember reading that in my earlier searches. The peak rpm sounds right too. 8000 rpm stock stroke piston speed is about equal to...
  • joeschuit
    joeschuit replied to the thread 61x topend and stroker cranks.
    Exhaust port width is 56mm at widest point, so about 66%.
Top Bottom